Extron Electronics ISM MTP UT 4DA Output Board - Manual (Page 2)

Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
68-1123-60
Rev A
02 09
ISM MTP UT 4DA Output Board Installation Notes, cont’d
9. Connect a control device to RS-232 insert 1/2 (for
outputs 1 and 2), or insert 3/4 (for outputs 3 and
4). This allows bidirectional, pass-through control
signals to and from the control device and the
MTP devices on ports 1 and 3, and unidirectional
pass-through signals from the control device on
ports 2 and 4. Ports 1 and 2 always receive the
same RS-232 command signal, but only port 1
allows for bidirectional communications. The
same is true for ports 3 and 4, where port 3 allows
for bidirectional communications (see right).
See below for board specific SIS ™ commands.
ISM MTP UT 4DA configuration menu
Using the front panel menu buttons (Menu and Next), the
ISM MTP UT 4DA board configuration menu can be accessed.
From the Output Configuration screen, press Next until reaching
the #x ISM MTP menu (see the image at right). Using the front
panel adjustment knobs ({ [), change the settings as desired.
Power up input and output devices and create the desired ties.
Board specific SIS commands table
Alternatively, the ISM MTP UT 4DA board can be configured with specific SIS commands.
N X! = ISM 824 output number, 3,5,7,8 (i.e. the slot/port occupied by the ISM MTP UT 4DA)
X@ = RS-232 number 0 = insert 1/2, 1= insert 3/4
X# = Setting value 0 = off, 1= on
X$
= Sub-output number (setting for each MTP output on each card) 1,2,3,4
Command ASCII
command
(host to switcher)
Response
(switcher to host)
Additional description
Local RS-232 ports
Enable EX! *X@ *1LRPT X! Lrpt X@ *1 ] Enable RS-232 insert X@ to
control output X! .
Disable EX! *X@ *0LRPT X! Lrpt X@ *0 ] Disable RS-232 insert X@
controlling output X! .
View EX! *X@ LRPT X#] View the RS-232 status X#
for
output X!
.
Output Pre-peaking
Turn on EX! *X$ *1OPEK X! Opek X$ *1 ] Turn pre-peaking on for output
X! to MTP sub-output X$ .
Turn off EX! *X$ *0OPEK X! Opek X$ *0 ] Turn pre-peaking off for output
X! to MTP sub-output X$ .
View
status EX! *X$ OPEK X#] View the pre-peaking status X#
for output X! .
RS-232 Insert 3/4
On
Next
Output Card
Configuration
Next
Prepeaking #x
On
RS-232 Insert 1/2
On
Select Ouptut
#x ISM MTP UT 4DA
Next
Next
RS-232 Commands
RS-232 Commands
INSERT 3/4
LOCAL
AUDIO OUTPUT
L R
1 2 3 4
BUFFERED OUTPUTS
RS 232
Tx Rx
INSERT 1/2
Tx Rx
ISM
M
TP UT 4D
A
Bidirectional
1 2 3 4
BUFFERED OUTPUTS
Unidirectional
Transmit (Tx)
Receive (Rx)
Ground (Gnd, )
© 2009 Extron Electronics. All rights reserved
.