Extron Electronics ISM VS Output Board - Manual (Page 4)

Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
68-1123-63
Rev A
08 10 © 2010 Extron Electronics. All rights reserved
.
www.extron.com
4
ISM VS Output Board
•
Setup Guide, cont’d
NOTE:
X! = Input number, 0-8
X@ = Output number, 1-8
X1) = Mode status, 1 = on, 0 = off
X1% = Picture adjustment (0 to 255)
X2! = Output resolution, 01 = 640x480, 02 = 800x600, 03 = 852x480, 04 = 1024x768,
07 = 1280x768, 08 = 1280x1024, 09 = 1360x765, 10 = 1365x768, 11 = 1366x768,
12 = 1365x1024, 13 = 1400x1050, 15 = 480p, 16 = 576p, 17 = 720p,18 = 1080i,19 = 1080p
X2@ = Refresh rate, 1 = 50 Hz, 2 = 60 Hz
X2% = User presets (1 to 3)
Board-specific SIS commands table
Command ASCII
command
(host to ISM)
Response
(ISM to host)
Additional description
Input selection
Video and audio X! *X@! OutX@•InX!•All] Tie video/audio input X! to X@ .
Video X! *X@& OutX@•InX!•RGB] Tie video input X! to output X@ .
Audio X! *X@$ OutX@•InX!•Aud] Tie audio input X! to output X@.
Output scaler rate
Set output rate X@ * X2!* X2@= RteX@ *X2!*X2@] Set output resolution/refresh rate
View X@= X2! *X2@] View resolution/refresh rate
User presets (1 to 3)
Recall preset X@ *X2%. X@RprX2%] Recalls user preset X2%.
Save preset X@ *X2%, X@SprX2%] Saves user preset X2%.
Edge smoothing filter
Set filter on/off 16*X@*X1)# X@FilX! *X1)] Set filter on or off.
View setting 16*X@# X1)] View setting.
Enhancement mode
Set mode on/off 52*X@*X1)# X@EhnX! *X1)] Set enhancement mode on or off.
View setting 52*X@# X1)] View setting.
Top blanking
Specify a value X@ *X1% ( X@BltX!*X1%] Set number of top lines to blank.
Increment value X@ +( X@BltX!*X1%] Increase number of lines to blank.
Decrement value X@ -( X@BltX!*X1%] Decrease number of lines to blank.
View X@ ( X1%] Show number of lines to blank.
Bottom blanking
Specify a value X@ *X1% ) X@BlbX!*X1%] Set number of bottom lines to
blank.
Increment value X@ +) X@BlbX!*X1%] Increase number of lines to blank.
Decrement value X@ -) X@BlbX!*X1%] Decrease number of lines to blank.
View X@ ) X1%] Show number of lines to blank.