Xylem F1000 PADDLEWHEEL FLOW METERS - Manual (Page 11)

5.0 HOW TO OPERATE THE F-1000
Note: The calibrated units of measure such as GPM, LPM, M3H, GALLONS, LITERS, CUBIC METERS, ect., And the decimal
point location are pre-programmed at the factory to standard flow ranges (see chart). Any unit of measure can be factory programmed.
Please contact the factory for details.
! The meter is shipped from the factory with 2 AAA batteries installed.
! When measuring continuous flow (i.e. 24 hours per day, 7 days per week), do not operate the meter in the upper 25% of the
calibrated flow range. The paddle speed in these high flow ranges is fast. Damage to the paddle may occur if the meter is
allowed to run continuously at the high flow rate, especially with corrosive or abrasive fluids.
Model F-1000-RB:The F-1000-RB is the basic rate meter. The meter will display the rate of flow from .01 through 999999 in
any engineering units. Some standard units of measure are GPM, GPH, GPD, LPM, LPH, LPD, M3H, etc.
Model F-1000-TB:The F-1000-TB is the basic totalizer meter. The meter will display the total flow amounts from .01 through
999999 in any engineering units. Some standard units of measure are GALLONS, LITERS, CUBIC METERS. Pressing and
holding the RESET button (located on the front panel) for at least 2.0 seconds resets the total to zero. This feature can be
disabled -- see Fig. 12 below.
Model F-1000-RT:The F-1000-RT is the rate and totalizer meter. The meter will display the flow rate amounts and the total flow
amounts from .01 through 999999 in any engineering units. Some standard units of measure are GALLONS PER MINUTE,
GALLONS PER HOUR, GALLONS PER DAY, LITERS PER MINUTE, LITERS PER HOUR, LITERS PER DAY, CUBIC
METERS PER HOUR, CUBIC METERS PER DAY. Pressing the RESET button (located on the front panel) toggles the display
between flow rate and total flow. Pressing and holding the RESET button for at least 2.0 seconds while the total flow value is
displayed will reset the total to zero. This feature can be disabled -- see Fig. 12 below.
!
!
!
F-1000 Page 10 F-1000 Page 11
2 1
-
+
Red wire
(Positive lead)
Black wire
(Negative lead)
Terminal blocks
(AC Coil sensor input)
Jumpers
(Front Panel Totalizer Reset
Enable/Disable)
Header pins
(Tail membrane connector)
Battery size: two AAA (1.5 V each)
Screw size: #4 x .50 Philip oval “A”
Mounting holes (x2)
Fig. 12
F-1000-RT Rate - Totalizer
® BLUE-WHITE INDUSTRIES
RESET
MODE
® BLUE-WHITE INDUSTRIES
F-1000-RB Flow Rate Meter
GPM
GALLONS PER MINUTE
F-1000-TB Flow Totalizer
® BLUE-WHITE INDUSTRIES
RESET
GALLONS
F-1000-RB F-1000-TB F-1000-RT
F-1000 Circuit Board
Jumper Not
Installed (open)
Jumper
Installed
JUMPER CONFIGURATION
Total flow reset
to zero Enable
(Factory default)
Total flow reset
to zero Disable
! The F-1000 is factory calibrated to ± 2% of full scale rate reading. When measuring total flow, accumulated error
over time must be considered. Accuracy is based on laboratory testing of nominal pipe dimensions. Your actual
accuracy will vary based on your actual pipe I.D. And other installation factors.
! Due to increased wear on the paddle and axle, continuous operation at the upper 25% of the flow range is not
recommended.
6.0 FLOW RANGES
MACHINED INLINE BODIES - Standard Flow Range #1 [ Min - Max]
2.00 - 20.00
Pipe Size
3/8” INLINE
1 /2” INLINE
3/4” INLINE
1.0” INLINE
1-1/2” INLINE
2.0” INLINE
GPM 1
48.0 - 480.0 .800 - 8.000
4.00 - 40.00
6.00 - 60.00
15.0 - 150.0
30.0 - 300.0
GPH 1
120 - 1200
360 - 3600
900 - 9000
1800 - 18000
GPD 1
1100 - 11000
2800 - 28000
5700 - 57000
8600 - 86000
21500 - 215000
43000 - 430000
240 - 2400
LPM 1
180 - 1800 3.00 - 30.00
7.00 - 70.00
15.0 - 150.0
25.0 - 250.0
60.0 - 600.0
100 - 1000
LPH 1
420 - 4200
900 - 9000
1500 - 15000
3600 - 36000
6000 - 60000
M3H 1
0.180 - 1.800
0.420 - 4.200
0.900 - 9.000
1.50 - 15.00
3.60 - 36.00
6.00 - 60.00
SADDLES - Standard Flow [Min - Max]
Pipe Size
1-1/2” IPS
2.0” IPS
3.0” IPS
4.0” IPS
6.0” IPS
8.0” IPS
GPM 1
15.0 - 150.0
30.0 - 300.0
60.0 - 600.0
100 - 1000
250 - 2500
400 - 4000
GPH 1
900 - 9000
1800 - 18000
3600 - 36000
6000 - 60000
15000 - 150000
24000 - 240000
GPD 1
21500 - 215000
43000 - 430000
86500 - 865000
144000 - 999999
360000 - 999999
575000 - 999999
10.0” IPS
12.0” IPS
600 - 6000
800 - 8000
36000 - 360000
48000 - 480000
865000 - 999999
N/A
LPM 1
60.0 - 600.0
100 - 1000
250 - 2500
400 - 4000
900 - 9000
1500 - 15000
LPH 1
3600 - 36000
6000 - 60000
15000 - 150000
24000 - 240000
54000 - 540000
90000 - 900000
M3H 1
6.00 - 60.00
15.0 - 150.0
24.0 - 240.0
54.0 - 540.0
90.0 - 900.0
2200 - 22000
3000 - 30000
132000 - 999999
180000 - 999999
132 - 1320
180 - 1800
MACHINED INLINE BODIES - Low Flow Range #2 [Min - Max]
.500 - 5.000
Pipe Size
3/8” INLINE
1 /2” INLINE
3/4” INLINE
1.0” INLINE
1-1/2” INLINE
2.0” INLINE
GPM 2
20.0 - 200.0 .400 - 4.000
.800 - 8.000
2.00 - 20.00
10.0 - 100.0
15.0 - 150.0
GPH 2
30.00 - 300.0
120 - 1200
600 - 6000
900 - 9000
GPD 2
550 - 5500
700 - 7000
1100 - 11000
2800 - 28000
14400 - 144000
21500 - 215000
48.0 - 480.0
LPM 2
60.0 - 600.0 1.00 - 10.00
2.00 - 20.00
3.00 - 30.00
7.00 - 70.00
40.0 - 400.0
60.0 - 600.0
LPH 2
120 - 1200
180 - 1800
420 - 4200
2400 - 24000
3600 - 36000
M3H 2
0.060 - 0.600
0.120 - 1.200
0.180 - 1.800
0.420 - 4.200
2.40 - 24.00
3.60 - 36.00
MACHINED INLINE BODIES - Low Flow Ranges #3, 4, 5, and 6 [Min - Max]
-
Pipe Size
3/8” INLINE
1 /2” INLINE
3/4” INLINE
1.0” INLINE
1-1/2” INLINE
2.0” INLINE
GPM 3
- -
-
-
6.00 - 60.00
10.0 - 100.0
GPM 4
-
-
2.00 - 20.00
6.00 - 60.00
GPM 5
-
-
-
-
1.00 - 10.00
4.00 - 40.00
-
GPM 6
-
-
-
-
-
2.00 - 20.00
-
LPM 3
-
-
-
25.0 - 250.0
40.0 - 400.0
-
LPM 4
-
-
7.00 - 70.00
25.0 - 250.0
-
LPM 5
-
-
-
-
4.00 - 40.00
15.0 - 150.0
LPM 6
-
-
-
-
-
7.00 - 70.00
IPS PIPES
MOLDED INLINE BODIES - Standard Flow Range #1 [Min - Max]
2.00 - 20.00
Pipe Size
3/8” INLINE
1 /2” INLINE
3/4” INLINE
1.0” INLINE
GPM 1
48.0 - 480.0 .800 - 8.000
3.00 - 30.00
5.00 - 50.00
GPH 1
120 - 1200
300 - 3000
GPD 1
1100 - 11000
2800 - 28000
4320 - 43200
7200 - 72000
180 - 1800
LPM 1
180 - 1800 3.00 - 30.00
7.00 - 70.00
11.0 - 110.0
20.0 - 200.0
LPH 1
420 - 4200
660 - 6600
1200 - 12000
M3H 1
0.180 - 1.800
0.420 - 4.200
0.660 - 6.600
1.20 - 12.00
MOLDED INLINE BODIES - Low Flow Range #2 [Min - Max]
.500 - 5.000
Pipe Size
3/8” INLINE
1 /2” INLINE
3/4” INLINE
1.0” INLINE
GPM 2
20.0 - 200.0 .400 - 4.000
.800 - 8.000
2.00 - 20.00
GPH 2
30.00 - 300.0
120 - 1200
GPD 2
550 - 5500
700 - 7000
1100 - 11000
2800 - 28000
48.0 - 480.0
LPM 2
60.0 - 600.0 1.00 - 10.00
2.00 - 20.00
3.00 - 30.00
7.00 - 70.00
LPH 2
120 - 1200
180 - 1800
420 - 4200
M3H 2
0.060 - 0.600
0.120 - 1.200
0.180 - 1.800
0.420 - 4.200
METRIC PIPES
Pipe Size
50 MM - PN 10 & PN 16
63 MM - PN 10 & PN 16
90 MM - PN 10 & PN 16
110 MM - PN 10 & PN 16
160 MM - PN 10 & PN 16
200 MM - PN 10 & PN 16
LPM 1
4200 - 42000 70.0 - 700.0
110 - 1100
230 - 2300
350 - 3500
720 - 7200
1150 - 11500
LPH 1
6600 - 66000
13800 - 138000
21000 - 210000
43000 - 430000
70000 - 700000
M3H 1
4.20 - 42.00
6.60 - 66.00
13.8 - 138.0
21.0 - 210.0
43.0 - 430.0
70.0 - 700.0
SADDLES - Standard Flow [Min - Max]
160 MM - PN 10
200 MM - PN 10
1700 - 17000
2700 - 27000
100000 - 1000000
170000 - 1700000
100 - 1000
170 - 1700
(Meet ASTM-D-1785)
(Meet DIN 8062)