Asus P5RD1-V Deluxe User Manual
Page 57

A S U S P 5 R D 1 - V D e l u x e
A S U S P 5 R D 1 - V D e l u x e
A S U S P 5 R D 1 - V D e l u x e
A S U S P 5 R D 1 - V D e l u x e
A S U S P 5 R D 1 - V D e l u x e
2 - 3 3
2 - 3 3
2 - 3 3
2 - 3 3
2 - 3 3
1 0 .
1 0 .
1 0 .
1 0 .
1 0 . Chassis intrusion connector (4-1 pin CHASSIS)
C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S )
C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S )
C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S )
C h a s s i s i n t r u s i o n c o n n e c t o r ( 4 - 1 p i n C H A S S I S )
This connector is for a chassis-mounted intrusion detection sensor or
switch. Connect one end of the chassis intrusion sensor or switch
cable to this connector. The chassis intrusion sensor or switch sends a
high-level signal to this connector when a chassis component is
removed or replaced. The signal is then generated as a chassis
intrusion event.
By default, the pins labeled “Chassis Signal” and “Ground” are shorted
with a jumper cap. Remove the jumper caps only when you intend to
use the chassis intrusion detection feature.
1 1 .
1 1 .
1 1 .
1 1 .
1 1 . IEEE 1394a connector (10-1 pin IE1394_1)
I E E E 1 3 9 4 a c o n n e c t o r ( 1 0 - 1 p i n I E 1 3 9 4 _ 1 )
I E E E 1 3 9 4 a c o n n e c t o r ( 1 0 - 1 p i n I E 1 3 9 4 _ 1 )
I E E E 1 3 9 4 a c o n n e c t o r ( 1 0 - 1 p i n I E 1 3 9 4 _ 1 )
I E E E 1 3 9 4 a c o n n e c t o r ( 1 0 - 1 p i n I E 1 3 9 4 _ 1 )
This connector is for the IEEE 1394a module. Connect the the IEEE
1394a module cable to this connector, then install the module to a
slot opening at the back of the system chassis.
Never connect a U S B c a b l e
U S B c a b l e
U S B c a b l e
U S B c a b l e
U S B c a b l e to the USB connectors. Doing so will
damage the motherboard!
P5RD1-V
®
P5RD1-V DELUXE Chassis intrusion connector
CHASSIS
+5VSB_MB
Chassis Signal
GND
(Default)
P5RD1-V
®
P5RD1-V DELUXE IEEE-1394 connector
1
TP
A1-
GND
TPB1-
+12V
GND
TP
A1+
GND
TPB1+
+12V
IE1394_1