Asus P5RD1-V Deluxe - Manual (Page 52)

2 - 2 8 2 - 2 8 2 - 2 8 2 - 2 8 2 - 2 8 C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
3 . 3 . 3 . 3 . 3 . S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s
( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] , S A T A 3 [ b l a c k ] ,
( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] , S A T A 3 [ b l a c k ] , ( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] , S A T A 3 [ b l a c k ] , ( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] , S A T A 3 [ b l a c k ] , ( 7 - p i n S A T A 1 [ b l a c k ] , S A T A 2 [ b l a c k ] , S A T A 3 [ b l a c k ] ,
S A T A 4 [ b l a c k ] )
S A T A 4 [ b l a c k ] ) S A T A 4 [ b l a c k ] ) S A T A 4 [ b l a c k ] ) S A T A 4 [ b l a c k ] )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can can create a
RAID 0, RAID 1, RAID 0+1, and JBODconfiguration. Refer to Chapter 5
for information on creating a RAID configuration.
P5RD1-V
®
P5RD1-V DELUXE SATA connectors
SATA1
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
SATA4
GND
RSATA_TXP4
RSATA_TXN4
GND
RSATA_RXP4
RSATA_RXN4
GND
SATA3
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND
SATA2
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
Enable the Serial ATA Controller item in the BIOS if you want to use the
Serial ATA RAID feature. See the S o u t h B r i d g e C o n f i g u r a t i o n
S o u t h B r i d g e C o n f i g u r a t i o n S o u t h B r i d g e C o n f i g u r a t i o n S o u t h B r i d g e C o n f i g u r a t i o n S o u t h B r i d g e C o n f i g u r a t i o n for
details.
• Due to chipset limitation, you cannot configure a RAID 0/JBOD set
across more than two hard disk drives.
• Install the Windows ® 2000 Service Pack 4 or the Windows ® XP
Service Pack1 or later when using Serial ATA.