Theatre Solution Lyric Auditorium Seating - Manual (Page 23)

22 Specifications Lyric Auditorium Seating
B. Seat Construction: Seat construction is comprised of an injection-molded polypropylene cover fastened
securely to an inner upholstered structural steel frame assembly. The outer seat cover shall have a
textured exterior surface and internal molded reinforcing ribs for a solid warp-free construction. The inner
seat frame assembly shall consist of a 7/8” dia. X 16 gauge steel tube formed with a waterfall front edge
and welded into a rigid assembly with (2) 11 gauge X 1” steel brackets and (1) 1/4” diameter steel rod. The
seat frame shall be fitted with a cast iron counterweight to insure automatic self-rising without the aid of
springs. A series of (7) 2” wide elastic suspension straps shall be stretched and woven in place and
fastened to the steel seat frame with 1/8” dia. steel hooks. Arch-spring and/or S-spring construction will not
be acceptable. A layer of 1 3/4” thick molded polyurethane foam shall be applied over the elastic webbing.
Foam shall be fire retardant and conform to the California Bureau of Home Furnishings Technical Bulletin
117. The upholstery cover shall be sewn and fitted to the seat assembly with collapsible assembly rings
and nylon tension cord.
The outer injection-molded seat cover and upholstered inner seat assembly shall be joined together with
cast aluminum mounting brackets. Seat widths of 19” and 21” shall be fitted with narrow style mounting
brackets. Seat widths of 20” and 22” shall be fitted with width-extending mounting brackets. The complete
seat assembly shall be assembled to the seat hinges using (2) special purpose M10 Hinge Bolts and (2)
special purpose M10 Hinge Pins which are specifically designed to accommodate installation tolerances.
C. Back Construction: Back construction is comprised of an injection-molded polypropylene cover fastened
securely to an inner upholstered structural steel frame assembly. The outer back cover shall have a
textured exterior surface and internal molded reinforcing ribs for a solid warp-free construction. The inner
back frame assembly shall consist of a 7/8” dia. X 16 gauge steel tube formed into an ergonomically
derived radius and welded into a rigid assembly with (2) 11 gauge X 1” steel brackets and (3) 1/4” diameter
steel rods. A series of (5) 2” wide elastic suspension straps shall be stretched and woven in place and
fastened to the steel seat frame with 1/8” dia. steel hooks. Arch-spring and/or S-spring construction will not
be acceptable. A layer of 1 1/4” thick molded polyurethane foam shall be applied over the elastic webbing.
Foam shall be fire retardant and conform to the California Bureau of Home Furnishings Technical Bulletin
117. The upholstery cover shall be sewn and fitted to the seat assembly with collapsible assembly rings
and nylon tension cord.
The outer injection-molded back cover and upholstered inner back assembly shall be joined together with
cast aluminum mounting brackets. Back widths of 19” and 21” shall be fitted with 3/8” thick mounting
brackets. Back widths of 20” and 22” shall be fitted with 7/8” thick mounting brackets. The complete back
assembly shall be supported by two 13 gauge formed steel brackets and two 3/8-16 hex head bolts and
shall be attached to the frame with (2) 1/4-20 machine screws.
D. Armrests: Shall be blow-molded high density polyethylene and curved to match the leg mounting plate.
The armrest will be fastened to the steel frame arm support with three #8 sheet metal screws.
E. Hinge: Shall be injection-molded of DuPont™ Zytel
®
801 nylon. The hinge shall be molded with
provisions to provide positive stop locations for the seat in both occupied and unoccupied positions. The
hinge shall be fitted with a plastic cover to eliminate all pinch points and shall include (2) 7/16” thick
urethane rubber pads to dampen noise upon the seat stop in both the vertical and horizontal positions.
Note: Dupont™ and Zytel ® are registered trademarks of E.I.du Pont de Nemours and Co. or its affiliates