3B Scientific Light Therapy__3B LASER NEEDLE, red laser light, 12x660 nm - Manual (Page 15)

26 27
10. Status, Warning and Fault Messages
The following table lists the status, warning and fault messages and their meaning.
10.1 Control Touch Pad:
Element/Message Explanation Action
LEDs on the front panel
Fig. 10.1.1 Fault display
The meaning is explained by the corres-
ponding fault message on the LCD
Check the message on the LCD •
If necessary, switch the unit off and back on •
Contact the Service team •
Fig. 10.1.2 Laser output is switched on -
Wireless interface connection status (Control Touch Pad to the Laser Unit)
Fig. 10.1.3 No connection to the Laser Unit Press the button again •
Switch the device off and unplug it from the mains •
Then plug the mains power back in and switch •
back on
Contact the Service team •
Fig. 10.1.4 There is a connection ot the Laser Unit
Rechargeable battery icons
Fig. 10.1.9 The battery charging level is displayed
Press on the icon to display further infor-
mation about the charging level
Fig. 10.1.10 Batteries are being charged
Fig. 10.1.11 Batteries not inserted or inserted with the
wrong polarity
Insert batteries into the battery compartment •
Check that the batteries are inserted the right •
way round
Rechargeable battery status displays: Display when the battery icon is pressed
Fig. 10.1.12 Batteries are not being charged
The battery charging level is displayed as
a percentage value
Fig. 10.1.13 Batteries are being charged
The battery charging level is displayed as
a percentage value
Fig. 10.1.14 Batteries not inserted or inserted with the
wrong polarity
Insert batteries into the battery compartment •
Check that the batteries are inserted the right •
way round
Warning messages when saving a program Confirm message with OK
Fig. 10.1.15 Saving is not possible as no laser diode
has been selected
Select at least one laser diode •
Fig. 10.1.16 Saving not possible as an invalid program
name has been entered (either no name
or a name that already exists)
Modify the program name •
Sound on / off
Fig. 10.1.17 Sound On
Fig. 10.1.18 Sound Off
10.2 Laser Unit:
Element/Message Explanation Action
LEDs on the patien component
Fig. 10.2.1 Fault display
The meaning is explained by the corres-
ponding LCD on the Control Touch Pad
Check the message on the LCD •
Unplug the • Laser Unit from the mains power
Then plug the mains power back in and switch •
back on
Contact the Service team •
Fig. 10.2.2 Laser Unit is switched on If the green LED does not light up, check whe- •
ther the plug-in power supply unit is connected
Contact the Service team •
Fig. 10.2.3 Laser output active (switched on)
Fault messages on the LCD Confirm message with OK
Fig. 10.1.5 Fault in communication
with the Laser Unit
Switch the device off and unplug it from the mains •
Then plug the mains power back in and switch •
back on
Contact the Service team •
Fig. 10.1.6 Laser power fault in the Laser Unit
Laser power is too low
Restart laser output •
If the fault reoccurs, unplug the Laser Unit from •
the mains power briefly
Then plug the mains power back in and switch •
back on
Contact the Service team •
Fig. 10.1.7 Laser power fault in the Laser Unit
Laser power is too high
Restart laser output •
If the fault reoccurs, unplug the Laser Unit from •
the mains power briefly
Then plug the mains power back in and switch •
back on
Contact the Service team •
Fig. 10.1.8 Temperature at the laser diodes >60°C
The unit switches automatically to a
frequency-modulated operating mode to
protect the laser diodes