beautypg.com

Dowco Power Sports Guardian EZ Zip Motorcycle Cover User Manual

Installation, Important, Care and cleaning

background image

Installation

Read instructions before using.
Unfold cover and remove Warranty Card and foam block from

vent area. Unzip rear zipper.
Position the front of the cover on motorcycle with the vent posi-

tioned approximately over the seating area. Starting in the front

wheel area, pull down over the windshield and “tuck” the elas-

tic hem under the centerline of the wheel.
Working toward the rear of the motorcycle, slide the cover

down the sides, avoiding “snag” points. Position the cover

around the rear of the motorcycle and close zipper.
Caution: To avoid damage to motorcycle finish, ensure

that the protective flap sewn behind the zipper rests

between the motorcycle and the zipper during cover instal-

lation.
Care should also be taken to avoid placing the black material

against hot engine components as melting or burning may

occur.
Caution: Mirrors, muffler ends, shifters, brakes and foot

pegs are common wear points. Do not allow fabric to

“snag” around them. Antennas are capable of puncturing

the cover – use extreme care.

Important

The aluminized heat-resistant coating is designed to protect

the cover from melting or burning when in contact with hot

engine parts, pipes and mufflers. Waiting approximately five-

ten minutes for cool-down before placing the cover on the

motorcycle will greatly increase the life of your cover.
Note: The aluminized coated fabric is similar to high quality

ironing board cover materials. The coating may experience

some minor “flaking” during normal use and this will not affect

the performance of the cover.
Grommet patches are provided to enable you to securely lock

the cover under the motorcycle. A cable lock or chain is rec-

ommended. However, should you be unable to unlock the

cover, it may have to be cut through the hem and grommet

area to be removed.

Care and Cleaning

Your cover requires very little maintenance. Normal dirt and

grime should be brushed off with a soft terry cloth or removed

with warm water and a mild detergent using a sponge or terry

cloth. The cover should be thoroughly dried before using.
Caution: Do not place in washing machine and do not

wring or twist the cover to remove moisture.
A water-repellant spray material, such as 3M Scotchguard

®

, is

recommended for increased water resistance.
Although protected with UV inhibitors, the fabric may fade in

direct sunlight after continuous use. This is normal wear.

Important

Failure to comply with the above directions may reduce the life

of your cover. If you have any questions or comments, please

contact either your dealer or DOWCO Inc..

Congratulations on your purchase of a GUARDIAN

®

EZ ZIP

motorcycle cover. Properly cared for, your cover will last for many

years of service. The GUARDIAN

®

EZ ZIP

is a premium all-weather cover manufactured from heavy-duty urethane coated poly-

ester fabric which has excellent water and weather resistance and may be used either inside or outside. An aluminized heat-resis-
tant coating is applied to the inside bottom portion so that the cover may be applied over warm engine pipes. Your cover also con-
tains an elastic shock cord that is sewn into a continuous hem, which eliminates the need for tie-downs. The integral vent allows
moisture to escape. The following information should be used to ensure maximum longevity.
Note: All GUARDIAN

®

EZ ZIP

covers are sized to fit specific motorcycles. It is very important that you have the correct one for

your application. If you are uncertain that your GUARDIAN

®

EZ ZIP

cover is correct, please contact your dealer or DOWCO Inc.

to verify your fit before attempting first-time use.
This cover is not designed for covering your motorcycle while it is trailered or in the back of a
pick-up truck.

INSTRUCTIONS FOR THE INSTALLATION OF
GUARDIAN

®

EZ ZIP

MOTORCYCLE COVER

Form # 00074

Revised 09/03

Printed in China

This cover must be completely removed prior to
starting or operating the vehicle. Failure to do
so could result in serious injury and/or property
damage.

In severely windy conditions, “ballooning” of the
cover may occur, which may result in the wind
causing the motorcycle to tip over. It is strongly
recommended that your motorcycle be sheltered
whenever high winds are expected. If sheltering
is not an option, facing into or rearward of strong
gusts may reduce the potential for wind damage.
Attaching a bungee cord or cable through grom-
met areas may also help prevent “ballooning” in
high winds.

4230 Clipper Drive Manitowoc, WI 54220 U.S.A.
Phone: (800) 558-7755 - Fax: (920) 682-5891
Visit our Web Site! - www.dowco-inc.com