B&B Electronics TB5P508SR-2PK - Quick Start Guide User Manual
Quick start guide

Documentation Number DRAFT pn#8096R003 VESR9xx-0712qsg
C
C
h
h
e
e
c
c
k
k
f
f
o
o
r
r
A
A
l
l
l
l
R
R
e
e
q
q
u
u
i
i
r
r
e
e
d
d
H
H
a
a
r
r
d
d
w
w
a
a
r
r
e
e
Vlinx VESR9xx module
This Quick Start Guide
CD with Vlinx Manager s/w and manuals
Network cable (not included)
Serial cable(s) (not included)
10 to 48V DC (6.0W) Power Supply (not
included)
Quick Start
Guide
Vlinx VESR9xx Serial
Servers
1
I
I
n
n
s
s
t
t
a
a
l
l
l
l
t
t
h
h
e
e
H
H
a
a
r
r
d
d
w
w
a
a
r
r
e
e
2
Connect a 10 to 48 VDC (58 VDC Max) power supply
(6.0 W required).
Connect the network cable from the serial server to a
network drop using a standard network cable.
Connect the serial device(s):
o
RS-232 with DB9: straight-through for DCE
device, null modem for DTE device
o
RS-232/422/485 with terminal blocks: see
Appendix D for pinouts
UL Installation Information
One Conductor Per Terminal
Use Copper Wire Only
Wire Size: 28 to 16 AWG
Tightening Torque: 5 KG-CM
Wire Temperature Rating: 105 C Minimum (Sized for 60 C
Ampacity)
80 C Maximum Surrounding Ambient Air Temperature
SUITABLE FOR USE IN CLASS 1, DIVISION 2 GROUPS A, B, C, AND D
HAZARDOUS LOCATIONS, OR NONHAZARDOUS LOCATIONS ONLY.
WARNING – EXPLOSION HAZARD – SUBSTITUTION OF ANY
COMPONENT MAY IMPAIR SUITABILITY FOR CLASS 1, DIVISION 2.
L
L
E
E
D
D
S
S
t
t
a
a
t
t
u
u
s
s
LED
STATUS
Ready
Blinks if system is operating correctly
Port 1
On indicates serial port open, blinks when data present on
serial port
Port 2
Same as Port 1
(Present on 2 port units only)
Link
On indicates Ethernet operating in 100BaseTX, blinks
when data present on Ethernet link
3
M
M
o
o
d
d
e
e
S
S
w
w
i
i
t
t
c
c
h
h
Hold in Mode switch for…
Result
0 to 2 seconds
Initiates a Hardware Reset
2 to 10 seconds
Enters Console Mode
More than 10 seconds
Resets to Factory Defaults
4
I
I
n
n
s
s
t
t
a
a
l
l
l
l
V
V
l
l
i
i
n
n
x
x
M
M
a
a
n
n
a
a
g
g
e
e
r
r
S
S
o
o
f
f
t
t
w
w
a
a
r
r
e
e
Insert the included CD and it should autostart
Follow the prompts to install the Vlinx Manager
software.
Note: Be sure you have administrative rights & disable firewalls.
5
S
S
e
e
t
t
u
u
p
p
V
V
l
l
i
i
n
n
x
x
M
M
a
a
n
n
a
a
g
g
e
e
r
r
S
S
o
o
f
f
t
t
w
w
a
a
r
r
e
e
Open Vlinx Manager: click
StartProgramsB&B
ElectronicsVlinxVlinx ManagerVESR
Serial Server
The Discovery page opens
To configure via the network, select Network.
If you know the IP address, select The device is
at this address, and type in the address.If not,
select I don’t know the IP address of the device.
Click Connect.
O
O
R
R
…
…
S
S
e
e
t
t
u
u
p
p
t
t
h
h
e
e
W
W
e
e
b
b
I
I
n
n
t
t
e
e
r
r
f
f
a
a
c
c
e
e
Open a browser and type the IP address of the
serial server in the Address Bar.
When the serial server is found, the
Configuration window appears.
6