B&B Electronics SD-150 Series - Datasheet - Manual

SPECIFICATION
SD-150B-12 SD-150C-12 SD-150D-12 SD-150B-24 SD-150C-24 SD-150D-24 MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
EFFICIENCY (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSION OTHERS
NOTE
PACKING
OVERLOAD
OVER VOLTAGE
DC CURRENT (Typ.)
12V 24V
12.5A 6.3A
0 ~ 12.5A 0 ~ 6.3A
150W 151.2W
120mVp-p 150mVp-p
1.0% 1.0%
11 ~ 16VDC 23 ~ 30VDC
0.5%
0.5%
0.3%
0.3%
2s, 50ms at full load (only D mode)
24ms at full load (only D mode)
B:19 ~ 36VDC C:36 ~ 72VDC D:72 ~144VDC or 85 ~ 132VAC
75%
6.8A/24V 6.8A/24V
77%
3.4A/48V 3.4A/48V
79%
2.7A/96V 2.7A/96V
77% 80% 82%
D:22.5A/96VDC
<0.75mA / 120VAC (SD-150D)
105 ~ 135% rated output power
16.8V ~ 20V/10% LOAD 31.5 ~ 37.5V/10% LOAD
Protection type : Hiccup mode, recovers automatically after fault condition is removed
Protection type : Hiccup mode, recovers automatically after fault condition is removed
-10 ~ +60 (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-20 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
199*110*50mm (L*W*H)
0.86Kg; 16pcs/14.5Kg/0.95CUFT
File Name:SD-150-SPEC 2010-07-27
EMS IMMUNITY
Compliance to EN55022 (CISPR22) Class B
IEC60950-1 CB approved by TUV (for D type only)
Compliance to ight EN61000-4-2,3,4,6,8; ENV50204, l industry level, criteria A
SAFETY STANDARDS
296.2K hrs min.(SD-150B) 289.9K hrs min.(SD-150C) 289K Hrs min.(SD-150D) MIL-HDBK-217F (25 )
150W Single Output DC-DC Converter
2:1 wide input range
Protections: Short circuit / Overload / Over voltage
1500VAC I/O isolation
Built-in EMI filter, low ripple noise
100% full load burn-in test
24V and 48V input voltage design refer to LVD
Low cost
High reliability
2 years warranty
Features :
S D - 1 5 0
s e r i e s
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH
ENVIRONMENT
SAFETY &
EMC
(Note 4)
PROTECTION
EMI CONDUCTION & RADIATION
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
1. All parameters NOT specially mentioned are measured at 24,48,96VDC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
(for D type only)