B&B Electronics DR-45 Series - Datasheet - Manual

SPECIFICATION
DR-4505 DR-4512 DR-4515 DR-4524 MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVER TEMPERATURE
SAFETY STANDARDS
HARMONIC CURRENT
EMS IMMUNITY
WORKING HUMIDITY
WORKING TEMP.
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSION OTHERS
NOTE
PACKING
OVERLOAD
OVER VOLTAGE
5V 12V 15V 24V
5A 3.5A 2.8A 2A
0 ~ 5A 0 ~3. 5A 0 ~ 2.8A 0 ~ 2A
25W 42W 42W 48W
100mVp-p 200mVp-p 240mVp-p
13.5 ~ 16.5V
480mVp-p
21.6 ~ 26.4V
2.0% 1.0% 1.0% 1.0%
10.8 ~ 13.2V 4.75 ~ 5.5V
1.0% 1.0% 1.0% 1.0%
1.0% 1.0% 1.0% 1.0%
800ms, 60ms/230VAC at full load
100ms/230VAC at full load
85 ~ 264VAC 120 ~ 370VDC
47 ~ 63Hz
72% 77% 77% 80%
1.5A/115VAC 0.75A/230VAC
COLD START 28A/115VAC 56A/230VAC
<1mA / 240VAC
105 ~ 150% rated output power
Protection type : Constant current limiting, recovers automatically after fault condition is removed
5.75 ~ 6.75V
Protection type : Shut off o/p voltage, clamping by zener diode
13.8 ~ 16.2V 17.25 ~ 20.25V 27.6 ~ 32.4V
Tj 135 typically (U1) detect on heat sink of power transistor
Protection type : Shut down o/p voltage, re-power on to recover
-10 ~ +50 (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-20 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6
364.6K hrs min. MIL-HDBK-217F (25 )
93*78*67mm (L*W*H)
0.31Kg; 48pcs/16.1Kg/1.3CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
File Name:DR-45-SPEC 2008-04-07
UL508, TUV EN60950-1 approved
Compliance to EN55011,EN55022 (CISPR22) Class B
Compliance to EN61000-3-2,-3
Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN55024, EN61000-6-2 (EN50082-2), heavy industry level, criteria A
45W Single Output Industrial DIN Rail Power Supply
D R - 4 5
s e r i e s
Universal AC input/Full range
Protections: Short circuit / Overload / Over voltage / Over temperature
Cooling by free air convection
Can be installed on DIN rail TS-35/7.5 or 15
UL 508(industrial control equipment)approved
LED indicator for power on
100% full load burn-in test
Fix switching frequency at 100KHz
3 years warranty
Features :
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
ENVIRONMENT
PROTECTION
SAFETY &
EMC
(Note 4)
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
EMI CONDUCTION & RADIATION