Rainbow Electronics MAX3345E User Manual
Page 2
MAX3344E/MAX3345E
±15kV ESD-Protected USB Transceivers
in UCSP with USB Detect
2
_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(V
CC
= 4V to 5.5V bypassed with 1µF to GND, GND = 0, V
L
= 1.65V to 3.6V, ENUM = V
L
, T
A
= T
MIN
to T
MAX
, unless otherwise
noted. Typical values are at V
CC
= 5V, V
L
= 2.5V, T
A
= +25°C.) (Note 2)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SUPPLY INPUTS (VCC, VTRM, VL)
Regulated Supply Voltage
Output
V
VTRM
Internal regulator
3.0
3.3
3.6
V
V
CC
Input Range
V
CC
4.0
5.5
V
V
L
Input Range
V
L
1.65
3.60
V
Operating V
CC
Supply Current
I
VCC
Full-speed transmitting/receiving at
12Mbps, C
L
= 50pF on D+ and D-
10
mA
Operating V
L
Supply Current
I
VL
Full-speed transmitting/receiving at
12Mbps
8
mA
Full-speed idle: V
D+
> 2.7V, V
D-
< 0.3V
340
450
Full-Speed Idle and SE0 Supply
Current
I
VCC(IDLE)
SE0: V
D+
< 0.3V, V
D-
< 0.3V
390
500
µA
Static V
L
Supply Current
I
VL(STATIC)
Full-speed idle, SE0, or suspend mode
12.5
µA
Suspend Supply Current
I
VCC(SUSP)
SUSP =
OE = high
40
µA
Disable-Mode Supply Current
I
VCC(DIS)
V
L
= GND or open
20
µA
D+/D- Disable-Mode
Load Current
I
D_(DIS)
V
L
= GND or open, V
D_
= 0 or +5.5V
5
µA
Sharing-Mode V
L
Supply
Current
I
VL(SHARING)
V
CC
= GND or open,
OE = low, SUSP =
high
20
µA
D+/D- Sharing-Mode
Load Current
I
D_(SHARING)
V
CC
= GND or open, V
D_
= 0 or +5.5V
20
µA
LOGIC-SIDE I/O
Input High Voltage
V
IH
SUSP, MODE, ENUM,
OE, VMO, VPO
2/3 x V
L
V
Input Low Voltage
V
IL
SUSP, MODE, ENUM,
OE, VMO, VPO
0.4
V
Output-Voltage High
V
OH
VPI, VMI, RCV, USB_DET; I
SOURCE
=
2mA
V
L
- 0.4
V
Output-Voltage Low
V
OL
VPI, VMI, RCV, USB_DET; I
SINK
= -2mA
0.4
V
Note 1: External 23.7Ω resistors connected to D+ and D-.
(All voltages refer to GND, unless otherwise noted.)
Supply Voltage (V
CC
) ...............................................-0.3V to +6V
Output of Internal Regulator (VTRM) ..........-0.3V to (V
CC
+ 0.3V)
Input Voltage (D+, D-) ..............................................-0.3V to +6V
System Supply Voltage (V
L
) .....................................-0.3V to +6V
RCV, SUSP, VMO, MODE, VPO,
OE, VMI,
VPI, USB_DET, ENUM...............................-0.3V to (V
L
+ 0.3V)
Short-Circuit Current (D+, D-) to V
CC
or
GND (Note 1) .........................................................Continuous
Maximum Continuous Current (all other pins) ..................±15mA
Continuous Power Dissipation (T
A
= +70°C)
16-Pin TSSOP (derate 9.4mW/°C above +70°C)...754mW (U16-2)
4
✕
4 UCSP (derate 8.2mW/°C above +70°C) ...659mW (B16-1)
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Bump Temperature (soldering) Reflow............................+235°C