Typical operating characteristics, Electrical characteristics (continued) – Rainbow Electronics MAX9595 User Manual
Page 6
R/G/B VIDEO LARGE-SIGNAL BANDWIDTH
vs. FREQUENCY
MAX9595 toc01
FREQUENCY (MHz)
GAIN (dB)
1
-5
-4
-3
-2
-1
0
1
2
3
4
-6
0.1
10
V
IN
= 1V
P-P
R
L
= 150Ω TO GNDVID
GROUP DELAY vs. FREQUENCY
MAX9595 toc02
FREQUENCY (MHz)
GROUP DELAY (ns)
1
20
40
60
80
100
120
0
0.1
10
Y VIDEO LARGE-SIGNAL BANDWIDTH
vs. FREQUENCY
MAX9595 toc03
FREQUENCY (MHz)
GAIN (dB)
1
-5
-4
-3
-2
-1
0
1
2
3
4
-6
0.1
10
V
IN
= 1V
P-P
R
L
= 150Ω TO GNDVID
Typical Operating Characteristics
(V
12
= 12V, V
VID
= V
AUD
= 5V, 0.1µF X5R capacitor in parallel with a 10µF aluminum electrolytic capacitor from V
AUD
to GNDAUD,
V
12
to GNDAUD, V
VID
to GNDVID no load, T
A
= 0°C to +70°C, unless otherwise noted. Typical values are at T
A
= +25°C.)
MAX9595
Audio/Video Switch for Dual SCART Connector
6
_______________________________________________________________________________________
ELECTRICAL CHARACTERISTICS (continued)
(V
12
= 12V, V
VID
= V
AUD
= 5V; 0.1µF X5R capacitor in parallel with a 10µF aluminum electrolytic capacitor from V
AUD
to GNDAUD,
V
12
to GNDAUD, and V
VID
to GNDVID; SET = 100kΩ nominal, R
LOAD
= 150Ω, T
A
= 0°C to +70°C, unless otherwise noted. Typical
values are at T
A
= +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNIT
Output Low Level
10kΩ to ground, internal TV,
11.4 < V
12
< 12.6
0
1.5
V
Output Medium Level
10kΩ to ground, external 16/9,
11.4 < V
12
< 12.6
5
6.5
V
Output High Level
10kΩ to ground, external 4/3,
11.4 < V
12
< 12.6
10
V
12
V
FAST SWITCHING SECTION (Note 4)
Input Low Level
0
0.4
V
Input High Level
1
3
V
Input Current
1
10
µA
Output Low Level
I
SINK
= 0.5mA
0
0.01
0.2
V
Output High Level
I
SOURCE
= 20mA, V
VID
- V
OH
0.75
2
V
Fast Switching Output to RGB
Skew
(Note 5)
30
ns
Fast Switching Output Rise Time
150Ω to ground
30
ns
Fast Switching Output Fall Time
150Ω to ground
30
ns
Note 1: All devices are 100% tested at T
A
= +25°C. All temperature limits are guaranteed by design.
Note 2: The settling time is measured from the 50% of the input swing to the 0.1% of the final value of the output.
Note 3: Maximum load capacitance is 200pF. All the listed parameters are measured at application’s inputs, unless otherwise
noted. See the Typical Application Circuits.
Note 4: Guaranteed by design.
Note 5: Difference in propagation delays of fast-blanking signal and RGB signals. Measured from 50% input transition to 50%
output transition. Signal levels to be determined.