Dc electrical characteristics (continued), Ac electrical characteristics – Rainbow Electronics MAX9395 User Manual
Page 3
MAX9394/MAX9395
2:1 Multiplexers and 1:2 Demultiplexers with
Loopback
_______________________________________________________________________________________
3
PARAMETER
SYM B O L CONDITIONS
MIN
TYP
MAX
UNITS
V
OUT_ _
or V
OUT_ _
= 0V
30
40
Output Short-Circuit Current
(Output(s) Shorted to GND)
|I
OS
|
V
ID
=
±100mV
(Note 4)
V
OUT_ _
=
V
OUT_ _
= 0V
17
24
mA
Output Short-Circuit Current
(Outputs Shorted Together)
|I
OSB
|
V
ID
=
±100mV, V
OUT_ _
= V
OUT_ _
(Note 4)
5
12
mA
SUPPLY CURRENT
R
L
= 100
Ω, EN_ _ = V
CC
53
65
Supply Current
I
CC
R
L
= 100
Ω, EN_ _ = V
CC
, switching at
670MHz (1.34Gbps)
53
65
mA
Note 1: Measurements obtained with the device in thermal equilibrium. All voltages referenced to GND except V
ID
, V
OD
, and
∆V
OD
.
Note 2: Current into the device defined as positive. Current out of the device defined as negative.
Note 3: DC parameters production tested at T
A
= +25°C and guaranteed by design and characterization for T
A
= -40°C to +85°C.
Note 4: Current through either output.
Note 5: Guaranteed by design and characterization. Limits set at ±6 sigma.
Note 6: t
SKEW
is the magnitude difference of differential propagation delays for the same output over the same condtions. t
SKEW
=
|t
PHL
- t
PLH
|.
Note 7: Measured between outputs of the same device at the signal crossing points for a same-edge transition under the same con-
ditions. Does not apply to loopback mode.
Note 8: Device jitter added to the differential input signal.
DC ELECTRICAL CHARACTERISTICS (continued)
(V
CC
= +3.0V to +3.6V, R
L
= 100
Ω ±1%, EN_ _ = V
CC
, V
CM
= +0.05V to (V
CC
- 0.6V) (MAX9394), V
CM
= +0.06V to (V
CC
- 0.05V)
(MAX9395), T
A
= -40°C to +85°C, unless otherwise noted. Typical values are at V
CC
= +3.3V, |V
ID
| = 0.2V, V
CM
= +1.2V, T
A
= +25°C.)
(Notes 1, 2, and 3)
AC ELECTRICAL CHARACTERISTICS
(V
CC
= +3.0V to +3.6V, f
IN
< 1.34GHz, t
R_IN
= t
F_IN
= 125ps, R
L
= 100
Ω ±1%, |V
ID
|
≥ 150mV, V
CM
= +0.075V to (V
CC
- 0.6V)
(MAX9394 only), V
CM
= +0.6V to (V
CC
- 0.075V) (MAX9395 only), EN_ _ = V
CC
, T
A
= -40°C to +85°C, unless otherwise noted. Typical
values are at V
CC
= +3.3V, |V
ID
| = 0.2V, V
CM
= +1.2V, f
IN
= 1.34GHz, T
A
= +25°C.) (Note 5)
PARAMETER
SYM B O L CONDITIONS
MIN
TYP
MAX
UNITS
SEL to Switched Output
t
SWITCH
Figure 3
1.1
ns
Disable Time to Differential
Output Low
t
PHD
Figure 4
1.7
ns
Enable Time to Differential Output
High
t
PDH
Figure 4
1.7
ns
Switching Frequency
f
MAX
V
OD
>
250mV
1.5
2.2
GHz
Low-to-High Propagation Delay
t
PLH
Figures 1, 5
340
567
720
ps
High-to-Low Propagation Delay
t
PHL
Figures 1, 5
340
562
720
ps
Pulse Skew |t
PLH
– t
PHL
|
t
SKEW
Figures 1, 5 (Note 6)
12.4
86
ps
Output Channel-to-Channel Skew
t
CCS
Figure 6 (Note 7)
16
87
ps
Output Low-to-High Transition
Time (20% to 80%)
t
R
f
IN_ _
= 100MHz, Figures 1, 5
112
154
187
ps
Output High-to-Low Transition
Time (80% to 20%)
t
F
f
IN_ _
= 100MHz, Figures 1, 5
112
152
187
ps
Added Random Jitter
t
RJ
f
IN_ _
= 1.34GHz, clock pattern (Note 8)
2
ps
(RMS)
Added Deterministic Jitter
t
DJ
1.34Gbps, 2
23
- 1 PRBS (Note 8)
60
91
ps
P-P