Uncle Milton Earth In My Room - Manual

3+
WallFriends-0250-0413-V01
Battery Installation
Tool required - Small Phillips head screwdriver
Requires 3 “AA” alkaline batteries (not included).
Requires 2 “AAA” alkaline batteries (not included).
Wall Mount
1. Using a Phillips head screwdriver, remove the battery cover as shown.
2. Insert 3 "AA" batteries as indicated in the battery compartment
and replace cover.
3. IMPORTANT! Switch your Wall Friend to either high or low brightness
before hanging on the wall.
PLEASE NOTE: The unit will not activate without the remote control.
Wall Installation
Note: Product is only intended to mount
on a vertical wall.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Caution: changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment. MANUFACTURED BY UNCLE MILTON INDUSTRIES, INC.
P.O. Box 6281
THOUSAND OAKS, CA 91359 USA
©2013 UMI. All rights reserved. ® and TM designate
trademarks of Uncle Milton Industries, Inc.
BATTERY SAFETY INFORMATION
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the toy before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Different types of batteries or new and used batteries are not to be mixed.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the toy.
• The supply terminals are not to be short-circuited.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
• Do not dispose of batteries in fire. Battery may explode or leak.
Remote Control
1. Using a Phillips
head screw-
driver, remove
the battery
cover as shown.
2. Insert 2 "AAA"
batteries as
indicated in the
battery
compartment
and replace
cover.
Operation
Light Setting
Slide the ON/OFF switch, located on the back of your Wall Friend, to either HI or
LOW brightness.
NOTE: For best illumination, use in a darkened room.
Wall Friend Activation
To activate your Wall Friend, press the button on your remote and hear your Wall
Friend greet you. Then, each time you press the button you’ll hear your Wall Friend
say a different phrase. Press and hold the button to turn your Wall Friend off.
Auto Off
Your Wall Friend will automatically shut off after approximately 15 minutes if
there is no manual interaction.
TM
Batteries not included
Requires 3 x 1.5V AA/LR6 batteries
AA/LR6
x3
Batteries not included
Requires 2 x 1.5V AAA/LR03 batteries
x2
AAA/LR03
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE — DO NOT DISCARD
Questions? Visit unclemilton.com
MADE IN CHINA
Hang
holes
Battery
cover
HI OFF L
OW
Instructions