Uncle Milton Farm In My Room Wild Walls User Manual

Farm in my room, Instruction manual, Scene set-up

13274

SCENE SET-UP

Install the Wallscape FX Activator

on your Wall

Before installing your Activator, move the function switch on the back
of the Activator from “Try Me” to “Play”. This will enable full special
effects functionality.

The Activator should only be mounted on a vertical surface.
For optimal results, place a nail or screw into the wall approximately
4 feet from the floor. Then, position the Activator onto the wall by
placing the hang hole on the back of activator directly over the nail
until securely in place.

Note: For rooms with ceilings higher than 8 feet, you may want to
position the activator higher than 4 feet to ensure that the light
sufficiently illuminates the wall and the ceiling.

Wall Decal Preparation

After removing the decals from the package, roll out the sheet and lay
flat for 24 – 48 hours until the sheet no longer wants to curl back up.

For best results apply the decals onto smooth, clean surfaces. The decals
may not stick to heavily textured surfaces. Do not apply to fresh paint or
wallpaper. Let the new paint/wallpaper dry for at least 3 weeks. Before
applying the decals to wallpaper or other delicate surfaces, test one in an
inconspicuous area. Keep the decals away from cribs and out of reach of
young children to prevent choking hazard.

Create your Scene by placing the Wall Decals
To apply each decal, carefully peel it off from the sheet. Then, place and
smooth the decal onto your wall in the desired location. To remove or
reposition each decal, just carefully peel it off from the wall. Kids can follow
the suggested scene layout or customize and create their own scene. For
optimal function with the light effects, please note the following suggestions
on wall decal placement:

• Begin with the lowest decal positioned 6” inches above the top of the

Activator.
• Then, place the bottom of the tractor decal approximately 15”

above the top of the Activator.
• Place all other decals around the featured animal decal but ideally no more

than 36 inches above the top of the Activator. This will help to

ensure that all decals are illuminated by the light cast.

On textured walls, periodically check the decals to make sure they are remaining flat
against the surface. Gently smooth any parts of the decal, that appear to be lifting off the
surface. Repeat as needed until the decals remain flat against the surface.

SCENE ACTIVATION

Now you can activate your scene using different programming modes on the
Wallscape FX Activator as follows:

TRY ME (10 second demo)
This is the factory default program and is used for in store demonstration. It is not
intended for home use and has limited functionality. For full functionality, move the
function switch on the back of the Wallscape FX Activator from “Try Me” to “Play”.

MODE 1 – FULL FUNCTIONALITY LIGHT & SOUND SHOW

Press the program button once to activate. This will enable full light

and sound special effects including the following:

• Music and undersea sound effects

• Light gently fading in and out, illuminating your wall and ceiling

• Synchronized lights and sounds that bring the scene to life.

In this mode, auto shut-off of the sound will occur approximately after 5 minutes

and auto shut-off of the light will occur approximately after 10 minutes.

MODE 2 – LIGHT SHOW ONLY

Press the program button two times to activate. This will enable full light functionality

but will not include any sound effects. Auto shut-off will occur approximately after

20 minutes.

MANUAL SHUT-OFF

To manually turn off the Wallscape FX Activator, press and hold down the program

button for approximately two seconds until the light and sound turns off.

BATTERY REPLACEMENT

Tool required - Small Phillips head screwdriver

Requires 3 AA/LR6 alkaline batteries.

1. Using a Phillips head screwdriver, remove the battery cover.

2. Insert 3 AA/LR6 alkaline batteries as indicated in the battery

compartment and replace cover.

3. IMPORTANT! Switch the Wallscape FX Activator to the PLAY

position before hanging on the wall.

DO NOT SKIP THIS STEP

Farm in My Room

Instruction Manual

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE — DO NOT DISCARD

Questions? Visit unclemilton.com

Function
Switch

Hang
Hole

Battery
Cover

TRY ME

PLAY

Wallscape FX Activator

Scene Set-Up

6” inches

15”

inches

36” inches

Top of Wallscape

FX Activator

PRODUCT STYLES

MAY VARY

Floor

4 Feet