Milton CAT D6T - Manual (Page 20)

20 D6T Track-Type Tractor specifications
Winch
Winch Model PA 56
Weight 1179 kg 2,600 lb
Oil Capacity 67 L 17.8 gal
Winch and Bracket Length 1210 mm 47.6 in
Winch Case Length 1210 mm 47.6 in
Winch Case Width 975 mm 38.4 in
Increased Tractor Length – STD 517 mm 20.4 in
Increased Tractor Length – XL/XW 517 mm 20.4 in
Increased Tractor Length – LGP 397 mm 15.6 in
Drum Diameter 254 mm 10 in
Drum Width 330 mm 13 in
Flange Diameter 504 mm 19.8 in
Drum Capacity – 22 mm (0.88 in) 88 m 290 ft
Drum Capacity – 25 mm (1.0 in) 67 m 220 ft
Drum Capacity – 29 mm (1.13 in) 67 m 220 ft
Ferrule Size (O.D.
ן Length)
54
ן
2.10
ן
67 mm 2.63 in
Standards
ROPS/FOPS ROPS meets criteria
SAE J395, SAE 1040
MAY 94, ISO 3471-1994/
FOPS meets ISO 3449-1992
Level II
Cab Meets appropriate
standards as listed below.
Brakes Brakes meet criterion
SAE J/ISO 10265 MAR99
• The operator sound exposure Leq (equivalent sound
pressure level) measured according to the work cycle
procedures specified in ANSI/SAE J1166 OCT 98 is 80 dB(A)
for cab offered by Caterpillar when properly installed and
maintained and tested with the doors and windows closed.
• Hearing protection may be needed when operating with
an open operator station and cab (when not properly
maintained or doors/windows open) for extended periods
or in noisy environment.
• The exterior sound pressure level for the standard machine
measured at a distance of 15 meters (49.2 ft) according to
test procedures specified in SAE J88 APR 95, mid-gear-
moving operation, is 85 dB(A).
Hydraulic Controls – Pump
RPM at rated Engine Speed – 1,965 rpm
Implement
RPM at rated Engine Speed – 2,625 rpm
Steering
Pump Output – Implement 189 L/min 49.9 gal/min
Pump Output – Steering 179 L/min 47.3 gal/min
Lift Cylinder Flow 189 L/min 49.9 gal/min
Tilt Cylinder Flow 80 L/min 21.1 gal/min
Ripper Cylinder Flow 189 L/min 49.9 gal/min
Angle Cylinder Flow – VPAT 170 L/min 44.9 gal/min
Hydraulic Controls – Main Relief Valve
Pressure Setting – Steering 41 700 kPa 6,048 psi
Pressure Setting – Implement 21 700 kPa 3,147 psi
(Non-VPAT)
Pressure Setting – Implement 24 440 kPa 3,545 psi
(VPAT)
Hydraulic Controls – Maximum Operating Pressure
(Non-VPAT)
Bulldozer – Lift 19 300 kPa 2,799 psi
Bulldozer – Tilt 19 300 kPa 2,799 psi
Ripper 19 300 kPa 2,799 psi
Hydraulic Controls – Maximum Operating Pressure
(VPAT)
Bulldozer – Lift 21 550 kPa 3,126 psi
Bulldozer – Tilt 21 550 kPa 3,126 psi
Bulldozer – Angle 21 550 kPa 3,126 psi
Ripper 19 300 kPa 2,799 psi
Ripper
Type Fixed Parallelogram
Number of Pockets 3
Overall Beam Width 2202 mm 87 in
Beam Cross Section 216
ן
8.5
ן
254 mm 10 in
Maximum Clearance Raised 511 mm 20.1 in
(under tip, pinned in bottom hole)
Maximum Penetration 500 mm 19.7 in
Maximum Penetration Force 6603 kg 14,557 lb
Pryout Force 9134 kg 20,137 lb
Weight – With One Shank 1634 kg 3,606 lb
Each Additional Shank 74 kg 163 lb