Milton CAT D10T - Manual (Page 13)

13
Blades
Type 10SU
Capacity
(SAE J1265) 18.5 m 3 24.2 yd 3
Width (over end bits) 4860 mm 15 ft 11 in
Height 2120 mm 6 ft 11 in
Digging Depth 674 mm 26.5 in
Ground Clearance 1497 mm 58.9 in
Maximum Tilt 993 mm 39.1 in
Weight* (without
hydraulic controls) 10 229 kg 22,551 lb
Total Operating
Weight** (with Blade
and Single-Shank
Ripper) 66 451 kg 146,499 lb
Type 10U
Capacity
(SAE J1265) 22 m 3 28.8 yd 3
Width (over end bits) 5260 mm 17 ft 3 in
Height 2120 mm 6 ft 11 in
Digging Depth 674 mm 26.5 in
Ground Clearance 1497 mm 58.9 in
Maximum Tilt 1074 mm 42.3 in
Weight* (without
hydraulic controls) 10 784 kg 23,775 lb
Total Operating
Weight** (with Blade
and Single-Shank
Ripper) 67 006 kg 147,723 lb
* * Includes blade tilt cylinder.
Add 840 kg (1,852 lb) for 10SU ABR blade.
Add 1629 kg (3,591 lb) for 10U ABR blade.
** Total Operating Weight: Includes hydraulic
controls, blade tilt cylinder, coolant,
lubricants, 100% fuel, ROPS, FOPS cab,
Blade, Single-Shank Ripper, 610 mm
(24 in) ES shoes, and operator.
Rippers
Type Single-Shank,
Adjustable
Parallelogram
Added Length 1760 mm 5 ft 9 in
Number of Pockets 1
Maximum Clearance
Raised (under tip,
pinned in bottom hole) 1058 mm 41.7 in
Maximum
Penetration
(standard tip) 1494 mm 58.8 in
Maximum
Penetration Force
(shank vertical) 205 kN 46,086 lb
Pry out Force 415.3 kN 93,363 lb
Weight (without
hydraulic controls) 7117 kg 15,690 lb
Total Operating
Weight* (with SU-
Blade and Ripper) 66 451 kg 146,499 lb
Type Multi-Shank,
Adjustable
Parallelogram
Number of Pockets 3
Added Length 1760 mm 5 ft 10 in
Overall Beam Width 2920 mm 115 in
Maximum Clearance
Raised (under tip,
pinned in bottom hole)
1045 mm 41.1 in
Maximum
Penetration
(standard tip) 876 mm 34.5 in
Maximum
Penetration Force
(shank vertical) 205 kN 46,086 lb
Pry out Force (Multi-
Shank Ripper with
one tooth) 415.3 kN 93,363 lb
Weight (one shank,
without hydraulic
controls) 7968 kg 17,566 lb
Additional Shank 526.2 kg 1,160 lb
Total Operating
Weight* (with SU-
Blade and Ripper) 67 302 kg 148,375 lb
* Total Operating Weight: Includes hydraulic
controls, blade tilt cylinder, coolant, lubricants,
100% fuel, ROPS, FOPS cab, SU-Blade,
Ripper, 610 mm (24 in) ES shoes, and
operator.
Winches
Winch Model Consult your
Cat Dealer for
installation
arrangements.
Standards
ROPS (Rollover Protective Structure) •
offered by Caterpillar for the machine
meets ROPS criteria SAE J1040 MAY94,
ISO 3471:1994.
FOPS (Falling Object Protective Structure)
•
meets SAE J/ISO 3449 APR98 Level II,
and ISO 3449:1992 Level II.
The operator Equivalent Sound Pressure Level
•
(Leq) is 80 dB(A) when “ISO 6396:2008” is
used to measure the value for an enclosed
cab. This is a dynamic cycle sound exposure
level. The cab was properly installed and
maintained. The test was conducted with
the cab doors and the cab windows closed.
The exterior sound pressure level for
•
the standard machine measured at a
distance of 15 meters according to the test
procedures specified in SAE J88 APR95,
mid-gear-moving operation, is 92 dB(A).