Spicer Steer Axle Beam Design Change Requires Different Design Thrust Bearings in “E” and “EFA” Series Steer Axles - Manual (Page 2)

Listed below is a reference chart for selecting kingpin kits. The bills of material are also shown below.
PRE-SIZED
DANA TIME BUSHING
P/N MODELS LINE TYPE NOTES
328345 E-1460I/W After Jan 1, 2000 Garlock
328343 E-1460I/W After Jan 1, 2000 Bronze
329404 E-1460I/W Before Jan 1, 2000 Garlock
329405 E-1460I/W Before Jan 1, 2000 Bronze
329432 EFA20F4, EFA-22T2, T5, EFA-24T2, T5 After Jan 1, 2000 Garlock
329433 EFA20F4, EFA-22T2, T5, EFA-24T2, T5 After Jan 1, 2000 Bronze
811525
EFA18F3, EFA20F4, EFA-22T2, T5, EFA-
24T2, T5
Before Jan 1, 2000 Garlock NOTE 1
329434
EFA18F3, EFA20F4, EFA-22T2, T5, EFA-
24T2, T5
Before Jan 1, 2000 Bronze
NOTE 1: Original kit still active and should only be used on models built BEFORE Jan 1, 2000.
NEW KIT !
NEW KIT !
NEW KIT !
NEW KIT !
NEW KIT !
BILL OF MATERIAL FOR DANA “E-1460I/W” MODEL KINGPIN KITS:
Qty Part-No Description
2 67592 LOCKNUT
2 220HC104 THRUST BRG
4 806334 BUSHING - PRESIZED (Garlock DX)
2 816239 DRAW KEY
4 971370 KNUCKLE CAP
2 817452 KNUCKLE PIN
2 817492 SHIM (.030)
4 817493 SHIM (.005)
2 817494 SHIM (.010)
4 819790 GREASE FITTING
4 820518 SEAL
4 971010 FOAM INSERT
(For Models E-1460I/W Made After Jan 1, 2000)
King Pin Kit: 328345
Qty Part-No Description
2 67592 LOCKNUT
2 220HC104 THRUST BRG
4 1460HD100 BUSHING - PRESIZED (Bronze)
2 816239 DRAW KEY
4 971370 KNUCKLE CAP
2 817452 KNUCKLE PIN
2 817492 SHIM (.030)
4 817493 SHIM (.005)
2 817494 SHIM (.010)
4 819790 GREASE FITTING
4 820518 SEAL
4 971010 FOAM INSERT
King Pin Kit: 328343
(For Models E-1460I/W Made After Jan 1, 2000)
Qty Part-No Description
2 67592 LOCKNUT
2 811523 THRUST BRG
4 806334 BUSHING - PRESIZED (Garlock DX)
2 816239 DRAW KEY
4 971370 KNUCKLE CAP
2 817452 KNUCKLE PIN
2 817492 SHIM (.030)
4 817493 SHIM (.005)
2 817494 SHIM (.010)
4 819790 GREASE FITTING
4 820518 SEAL
4 971010 FOAM INSERT
4 816294 O-RING GASKET
(For Models E-1460I/W Made Before Jan 1, 2000)
King Pin Kit: 329404
Qty Part-No Description
2 67592 LOCKNUT
2 811523 THRUST BRG
4 1460HD100 BUSHING - PRESIZED (Bronze)
2 816239 DRAW KEY
4 971370 KNUCKLE CAP
2 817452 KNUCKLE PIN
2 817492 SHIM (.030)
4 817493 SHIM (.005)
2 817494 SHIM (.010)
4 819790 GREASE FITTING
4 820518 SEAL
4 971010 FOAM INSERT
4 816294 O-RING GASKET
King Pin Kit: 329405
(For Models E-1460I/W Made Before Jan 1, 2000)
This bulletin contains product information.
Dana Corporation is not committed or liable for canvassing existing product.
2