Focus Foodservice Enclosure Panels on Wire Shelving - Assembly Instructions - Manual

ASSEMBLY INSTRUCTIONS
Enclosure Panels on Wire Shelving
FOODSERVICE, LLC
CAUTION: INSPECT CONTENTS IMMEDIATELY TO ENSURE PRODUCT WAS NOT DAMAGED DURING SHIPPING.
Assemble Wire Shelving Unit (See Diagram 1)
Step 1 For mobile version, install casters into bottoms of posts.
Step 2 Choose the desired height of the bottom shelf (for added stability, it is recommended that the bottom shelf is installed no
more than 6"(2 – 3 lines) from the floor and the top shelf no more than 6"(2 – 3 lines) from the top.) Snap two (2) tapered
sleeves, with the word UP on top, at the desired height on each post. Shelves can be adjusted every 1". (Note: Double
grooves in the posts are placed every 8th groove for simple shelf height reference.)
Step 3 Place shelf on its side, making sure the wider portion of the four (4) round shelf collars are facing the bottom of the unit,
slide the top of the posts through the round shelf collars on each corner of the shelves. Push the shelves firmly onto the
tapered sleeves.
Step 4 After installing the bottom shelf, set the unit upright.
Step 5 Snap the tapered sleeves into place on posts at the next desired shelf height. Slide the shelf down from the top of the posts
onto the tapered sleeves and repeat this step for the remaining shelves. Note: A rubber mallet may be used to tap each corner
of the shelves so they firmly install onto the tapered sleeves.
Note: The leg levelers may need to be utilized in order to make the unit level or flush against the wall.
Attach Enclosure Panels (See Diagram 2)
Step 6 Place (2) S-hooks Assemblies such that they slide down over the top portion of each truss on the top shelf of the shelving
unit. Make sure to space the S-hooks Assemblies so that they are approx. 4" from the shelving collars and aligned to the
second square from each end of the side panels.
Step 7 Attach the side panels: The (2) horizontal bars should face toward the shelving unit. Place the side panel onto the already
positioned S-hooks. Make sure that the position of the S-hooks Assemblies are positioned on second horizontal bar.
Step 8 Secure the side panels: Secure the S-hook Assemblies to the panel using the nut and bolt. Secure the bottom panel to the
bottom shelf truss using C-Channel Bracket Assemblies. Space each approx. 3" from shelving collar.
Step 9 Tighten all screws to ensure secure fit. Repeat process for remaining side panel and rear panels.
Enclosure Panel Requirements
Ends- Panels required for EACH end according
to shelf widths as follows
Nominal
Post Height
Nominal Shelf Width
18" (45.7 cm) 21" (53.0 cm) 24" (61.0 cm) 30" (76.0 cm) 36" (91.4 cm)
54" (137.2 cm) (1) FEP1854CH (1) FEP1854CH (1) FEP2454CH (2) FEP1854CH (1) FEP1854CH & (1) FEP2454CH
63" (160.0 cm) (1) FEP1863CH (1) FEP1863CH (1) FEP2463CH (2) FEP1863CH (1) FEP1863CH & (1) FEP2463CH
74" (188.0 cm) (1) FEP1874CH (1) FEP1874CH (1) FEP2474CH (2) FEP1874CH (1) FEP1874CH & (1) FEP2474CH
Backs - Requires multiple panels IN QUANTIES SHOWN for specific shelf lengths:
Nominal
Post Height
Nominal Shelf Length
30" (76.0 cm) 36" (91.4 cm) 42" (106.6 cm) 48" (122.0 cm) 54" (137.0 cm) 60" (152.4 cm) 72" (182.9)
54" (137.2 cm) (2) FEP1854CH (1) FEP1854CH & (1) FEP2454CH (2) FEP2454CH (2) FEP1854CH & (1) FEP2454CH (1) FEP1854CH & (2) FEP2454CH (3) FEP2454CH (1) FEP1854CH & (3) FEP2454CH
63" (160.0 cm) (2) FEP1863CH (1) FEP1863CH & (1) FEP2463CH (2) FEP2463CH (2) FEP1863CH & (1) FEP2463CH (1) FEP1863CH & (2) FEP2463CH (3) FEP2463CH (1) FEP1863CH & (3) FEP2463CH
74" (188.0 cm) (2) FEP1874CH (1) FEP1874CH & (1) FEP2474CH (2) FEP2474CH (2) FEP1874CH & (1) FEP2474CH (1) FEP1874CH & (2) FEP2474CH (3) FEP2474CH (1) FEP1874CH & (3) FEP2474CH