Focus Foodservice 930088 Mobile 3 Shelf Garment Rack - Assembly Instructions - Manual

SHELVING
ASSEMBLY
INSTRUCTIONS
Call Customer Service at 1.800.968.3918 | Fax 1.800.968.4129 | www.focuspg.com
Model# 930088 |
Mobile 3 Shelf Garment Rack
16" x 36" x 77 3 / 8 " (H)
DIAgRAM 1 DIAgRAM 2 DIAgRAM 3
Top Top
rev. 072106
Material List
24 ea. –Plastic Tapered Sleeves
4 ea. – Industrial Casters – 2 Locking
8 ea. – Posts
1 ea. – Garment Bar
2 ea. – Garment Bar Hangers
3 ea. – 16˝ x 36˝ Shelves
2 ea. – Bolts
4 ea. – Threaded Post Jointers
(Installed in Posts)
2 ea. – Garment Bar Hangers
Note: Please dispose of loose,
round plastic pieces. These are
used to separate the shelves for
shipping purposes.
Helpful Hint: When placing the plastic tapered sleeves onto the posts (Diagram #2), slide the
plastic tapered sleeves up or down on the post until you feel it “snap” into the lines or grooves of the
post. It is normal to have a slight gap in-between the two pieces of the plastic tapered sleeves when
it is placed on the post.
Step 1 Screw posts tightly together. (See Diagram #1) Threaded post jointers are
pre-installed for your convenience. (The top post sections have plastic end
caps on one end and the bottom posts have threaded holes for
installing the casters).
Step 2 Install industrial casters by screwing them into the threaded holes in the bottom of the
posts. (See Diagram #2)
Step 3 Choose the desired height of the bottom shelf (for added stability, it is recommended
that the bottom shelf is installed no more than 6˝(2 - 3 lines) from the floor and the
top shelf no more than 6˝(2 - 3 lines) from the top.) Snap the plastic tapered sleeves,
(with the arrow facing up and/or the narrow ends of the tapered plastic sleeves
toward the top of the unit), at the desired height on each post (See Diagram #2).
Shelves can be adjusted every 1˝. (Note: Double grooves are placed every 8th groove
for simple shelf placement.)
Step 4 Place shelf on its side, making sure the wider portion of the four collars are facing the
bottom of the unit, slide the top of the posts through the round collars on each
corner of the shelves (with lip of shelf facing down) (See Diagram #2) Push the
shelves firmly onto the plastic tapered sleeves.
Step 5 After installing the bottom shelf and casters, set the unit upright
Step 6 Snap the plastic tapered sleeves into place on posts at the next desired shelf height.
Slide the shelf down from the top of the posts onto the plastic tapered sleeves and
repeat this step for the remaining shelves. (Note: A rubber mallet may be used to tap
each corner of the shelves so they firmly install onto the plastic tapered sleeves.)
Step 7 Installing The Garment Bar:
A. Insert a bolt through the hole on the bottom of one of the garment bar hangers.
Screw the bolt into the end of the garment bar so the hook on the garment bar
hanger is facing inward. Make sure the screw is tightly in place.
B. Repeat Step A to install the other garment bar hanger.
C. The garment bar hangers will attach to the outside lip of the shelf. Make sure
one of the cross wires of the shelf is in the notch of the garment bar hanger.
(See Diagram #3)
WARNINg: HEAVY OBJECTS MUST BE PLACED--NOT DROPPED--
ONTO THE SHELVES!!
Note: Heaviest objects must be stored on lower shelves and lighter objects on upper shelves!!