Focus Foodservice Enclosure Panels on Wire Shelving with Aluminum Truck Dolly - Specification Sheets - Manual

ASSEMBLY INSTRUCTIONS
Enclosure Panels on Wire Shelving with Aluminum Truck Dolly
FOODSERVICE, LLC
CAUTION: INSPECT CONTENTS IMMEDIATELY TO ENSURE PRODUCT WAS NOT DAMAGED DURING SHIPPING.
Assemble Wire Shelving Unit to Truck Dolly
Step 1 Unpack carton, identify and confirm quality of components.
Step 2 Before assembly of shelving unit to Truck Dolly, unscrew the leveling feet on the posts (See Diagram 1).
Step 3 Attach the posts to Truck Dolly frame, using leveling feet and washers and tighten down (See Diagram 2).
Step 4 Choose the desired height of the bottom shelf (for added stability, it is recommended that the bottom shelf is installed no
more than 6"(2 – 3 lines) above the truck dolly and the top shelf no more than 6"(2 – 3 lines) from the top.) Snap two (2)
tapered sleeves, with the word UP on top, at the desired height on each post. (See Diagram 3) Shelves can be adjusted
every 1". (Note: Double grooves in the posts are placed every 8th groove for simple shelf height reference.)
Step 5 Snap the tapered sleeves into place on posts at the next desired shelf height. Slide the shelf down from the top of the posts
onto the tapered sleeves and repeat this step for the remaining shelves. (Note: A rubber mallet may be used to tap each
corner of the shelves so they firmly install onto the tapered sleeves.)
Attach Enclosure Panels (See Diagram 4)
Step 6 Place (2) S-hooks Assemblies such that they slide down over the top portion of each truss on the top shelf of the shelving
unit. Make sure to space the S-hooks Assemblies so that they are approx. 4" from the shelving collars and aligned to the
second square from each end of the side panels.
Step 7 Attach the side panels: The (2) horizontal bars should face toward the shelving unit. Place the side panel onto the already
positioned S-hooks. Make sure that the position of the S-hooks Assemblies are positioned on second horizontal bar.
Step 8 Secure the side panels: Secure the S-hook Assemblies to the panel using the nut and bolt. Secure the bottom panel to the
bottom shelf truss using C-Channel Bracket Assemblies. Space each approx. 3" from shelving collar.
Step 9 Tighten all screws to ensure secure fit. Repeat process for remaining side panel and rear panels.
Enclosure Panel Requirements
Ends- Panels required for EACH end according to shelf widths as follows
Nominal
Post Height
Nominal Shelf Width
18" (45.7 cm) 21" (53.0 cm) 24" (61.0 cm) 30" (76.0 cm) 36" (91.4 cm)
54" (137.2 cm) (1) FEP1854CH (1) FEP1854CH (1) FEP2454CH (2) FEP1854CH (1) FEP1854CH & (1) FEP2454CH
63" (160.0 cm) (1) FEP1863CH (1) FEP1863CH (1) FEP2463CH (2) FEP1863CH (1) FEP1863CH & (1) FEP2463CH
74" (188.0 cm) (1) FEP1874CH (1) FEP1874CH (1) FEP2474CH (2) FEP1874CH (1) FEP1874CH & (1) FEP2474CH
Backs - Requires multiple panels IN QUANTITIES SHOWN for specific shelf lengths:
Nominal
Post Height
Nominal Shelf Length
30" (76.0 cm) 36" (91.4 cm) 42" (106.6 cm) 48" (122.0 cm) 54" (137.0 cm) 60" (152.4 cm) 72" (182.9)
54" (137.2 cm) (2) FEP1854CH (1) FEP1854CH & (1) FEP2454CH (2) FEP2454CH (2) FEP1854CH & (1) FEP2454CH (1) FEP1854CH & (2) FEP2454CH (3) FEP2454CH (1) FEP1854CH & (3) FEP2454CH
63" (160.0 cm) (2) FEP1863CH (1) FEP1863CH & (1) FEP2463CH (2) FEP2463CH (2) FEP1863CH & (1) FEP2463CH (1) FEP1863CH & (2) FEP2463CH (3) FEP2463CH (1) FEP1863CH & (3) FEP2463CH
74" (188.0 cm) (2) FEP1874CH (1) FEP1874CH & (1) FEP2474CH (2) FEP2474CH (2) FEP1874CH & (1) FEP2474CH (1) FEP1874CH & (2) FEP2474CH (3) FEP2474CH (1) FEP1874CH & (3) FEP2474CH