Bosch GOS 10,8 V-LI Professional - Manual (Page 11)

English | 11
Bosch Power Tools 1 609 92A 00D | (11.12.12)
4 Reduce-brightness button “–”
5 Display
6 Camera cable
7 Camera head
8 Camera lens
9 Illumination light in camera head
10 Battery pack*
11 Battery unlocking button
12 Camera cable, extension*
13 Socket sleeve of camera connection
14 Camera connection
15 Magnet
16 Hook
17 Mirror
18 Video output socket
19 Video cable
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Assembly
 Before any work on the inspection camera itself (e.g.
assembling, maintenance, etc.) as well as when trans-
porting and storing, remove the battery from the in-
spection camera.
Battery Charging
 Use only the battery chargers listed on the graphics
page. Only these battery chargers are matched to the lith-
ium-ion battery used in your inspection camera.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The Lithium-Ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Battery Charge-control Indication
When the inspection camera is switched on, the charge con-
dition of the battery is indicated on the display
5:
Removing the battery
To remove the battery
10, press the battery unlocking but-
tons 11 and pull the battery toward the rear out of the inspec-
tion camera. Do not exert any force when doing this.
Mounting the Camera Cable (see figure A)
For operation of the inspection camera, the camera cable 6
must be mounted to the hand unit 1.
Insert the camera cable 6 into the camera connection 14 in
such a manner that the pin of the camera cable engages into
the opening of the camera connection as shown in the figure.
Slide the socket sleeve
13 on the camera connection over the
camera cable and hand-tighten in clockwise direction.
To remove the camera cable 6, unscrew socket sleeve 13 in
anticlockwise direction and pull the camera cable off.
Mounting the Camera Cable Extension
(Accessory)
To mount a camera cable extension 12, the mounted camera
cable 6 must be removed.
Then, mount the extension 12 onto camera connection 14 as
described under “Mounting the Camera Cable” and tighten.
If required, further extensions can be mounted in the same
manner. However, the image quality decreases when exceed-
ing a total length approx. 10 m (incl. camera cable).
Screw the camera cable 6 onto the last extension 12 as de-
scribed under “Mounting the Camera Cable”.

Check if the camera cable and the extension are firmly
connected. The camera cable and the extension are only
water-tight when firmly connected. Untight connections
increase the risk of an electric shock or damage to the in-
spection camera.
Digital Inspection Camera GOS 10,8 V-LI
Article number 3 601 B41 000
Rated voltage V= 10.8
Operating temperature °C –20...+65
Storage temperature (hand unit
without battery)
°C –30...+80
Relative humidity % 5 –95 1)
Smallest bending radius of camera
cable
mm 120
Diameter of camera head mm 17/9.5
Depth-of-field range of camera
lens
mm 38 –

Display size mm 68.6
Display resolution 320 x 240
Format of video output NTSC
Operating life time, approx. h/Ah 11.5
Weight according to
EPTA-Procedure 01/2003
kg 0.68
Dimensions (length x width x
height)
mm 166 x 66 x 45
1) Free of moisture condensation
Indication Capacity
>1/2
<1/2
Reserve
OBJ_BUCH-1311-003.book Page 11 Tuesday, December 11, 2012 9:33 AM