9 4 ) r – JVC GR-D21 User Manual
Page 31
EN
31
USING THE REMOTE CONTROL UNIT
!
@
9
4
)
r
#
● Make sure to set “S/AV INPUT” to “OFF” in the Menu
Screen (GR-D31 only,
੬
pg. 24).
● Set the video out select switch of the cable adapter as
required:
Y/C
: When connecting to a TV or VCR which accepts
Y/C signals and uses an S-Video cable.
CVBS : When connecting to a TV or VCR which does not
accept Y/C signals and uses an audio/video
cable.
● When editing on a VCR equipped with a DV input
connector, an optional DV cable can be connected
instead of an S-Video cable and audio/video cable.
To Remote PAUSE
or R.A.EDIT
TV
To PAUSE IN
$
Editing cable***
Audio/Video cable
(provided)
*
Connect when an S-Video cable is not used.
** When connecting cables, open this cover.
*** Provided with the optional Remote Control kit
RM-V717KITU.
Connector
cover**
To AV
*
To EDIT
(
To
S-VIDEO
)
Programme
Random
Assemble
Editing Menu
1
2
3
4
5
6
7
8
– – : – – ~
~
~
~
~
~
~
~
– –
N
I
OUT
MODE
– – : – –
0 : 00
0
TOTAL
CODE
T I ME
VCR
“Y/C”/“CVBS”
video out
select switch
If your VCR has the
SCART connector,
use the provided
cable adapter.
To AUDIO, VIDEO*
and
-IN
connectors
5
If using a Fade/Wipe at the beginning of the scene,
press FADE/WIPE
9
on the remote control.
• Cycle through the effects by pressing repeatedly, and
stop when the one you want is displayed.
6
At the beginning of the scene, press EDIT IN/OUT
@
on the remote control. The Edit-In position appears
in the Random Assemble Editing Menu.
7
At the end of the scene, press EDIT IN/OUT
@
. The
Edit-Out position appears in the Random Assemble
Editing Menu.
8
If using a Fade/Wipe at the end of the scene, press
FADE/WIPE
9
.
• Cycle through the effects by pressing repeatedly, and
stop when the one you want is displayed.
• If you select a Fade/Wipe effect for an Edit-Out point,
the effect is automatically applied to the following
Edit-In point.
• When you use Fade/Wipe effects, that time is
included in the total time.
9
If using Playback Special Effects, press EFFECT
!
(
੬
pg. 28).
10
Repeat steps 6 through 9 to register additional
scenes.
• To change previously registered points, press
CANCEL
#
on the remote control. The registered
points disappear, one at a time, from the most
recently registered point.
• If you are not using Fade/Wipe or Programme AE with
special effects, repeat steps 6 and 7 only.
NOTES:
● When choosing a scene, set Edit-In and Edit-Out points
so that there is a relatively large difference between
them.
● If the search time for an in-point exceeds 5 minutes, the
recording deck’s Record-Standby mode will be cancelled
and editing will not take place.
● If there are blank portions before or after the Edit-In and
Edit-Out points, a blue screen may be included in the
edited version.
● Since time codes register time only as accurately as
seconds, the time code total time may not match the total
programme time exactly.
● Turning off the camcorder’s power erases all registered
Edit-In and Edit-Out points.
SELECT SCENES
4
Point the remote control at the camcorder’s remote
sensor. Press PLAY (4)
)
and then press R.A.EDIT
ON/OFF
r
on the remote control.
The Random Assemble Editing Menu appears.
S-Video cable
(optional)
Continued on next page.
GR-D31/21EK 28-33
02.12.19, 9:15 PM
31