Yamaha CLP-990M EN User Manual
Clp-990, Clp-990m, Owner’s manual
CLP-990
Owner’s manual
IMPORTANT
Check your power supply
Make sure that your local AC mains voltage
matches the voltage specified on the name
plate on the bottom panel. In some areas a
voltage selector may be provided on the bottom
panel of the main keyboard unit near the power
cord. Make sure that the voltage selector is set
for the voltage in your area. The voltage
selector is set at 240V when the unit is initially
shipped. To change the setting use a “minus”
screwdriver to rotate the selector dial so that
the correct voltage appears next to the pointer
on the panel.
CLP-990M
Table of contents
Document Outline
- PRECAUTIONS
- Table of contents
- Application Index Use this index to find reference pages that may be helpful for your application...
- Handling the Floppy Disk Drive(FDD) and Floppy Disk
- Maintenance
- Included Accessories
- Features
- Before Using the Clavinova
- Part Names
- Listening to the Demonstration Tunes
- Listening to 50 Piano Preset Songs
- Selecting and Playing Voices
- Recording Your Performance
- Saving Recorded Songs and Handling the Files...[FILE]
- Clavinova memory
- Basic file operation
- Saving recorded or other songs to Clavinova Storage memory...[SaveToMemory]
- Saving recorded or other songs to floppy disk...[SaveToDisk]
- Deleting songs in Clavinova Storage memory or a floppy disk...[DeleteSong]
- Renaming a song...[RenameSong]
- Copying data from one floppy disk to another...[CopyDisk]
- Formatting a floppy disk...[FormatDisk]
- Changing the type of characters on screen...[CharacterCode]
- Playing Back Recorded Songs and Commercially-available Music Data
- Connections
- Detailed Settings
- Detailed settings for recording and playback [SONG SETTING]
- Correcting note timing [Quantize]
- Specifying whether playback starts immediately along with the first voicing [QuickPlay]
- Auditioning the channels [ChannelListen]
- Deleting data from each channel [ChannelClear]
- Specifying the range and playing back repeatedly [FromToRepeat]
- Playing back the phrase specified by the phrase number [PhraseMark]
- Playing back a song repeatedly [SongRepeat]
- Detailed settings for the metronome METRONOME [SETTING]
- Detailed settings for the voices [VOICE SETTING]
- Setting the octave [Octave]*
- Setting the volume level [Volume]*
- Setting the position of right and left channels [Pan]*
- Fine tuning the pitch (only in Dual mode) [Detune]
- Selecting the reverb type [ReverbType]
- Setting the reverb depth [ReverbSend]*
- Selecting the chorus type [Chorus Type]
- Setting the chorus depth [ChorusSend]*
- Setting the chorus on/off [ChorusOnOff]
- Selecting the variation effect type [VariationType]
- Setting the variation effect depth [VariationSend]*
- Setting the touch sensitivity [TouchSense]*
- Setting the right pedal function [RPedal]
- Setting the center pedal function [MPedal]
- Setting the left pedal function [LPedal]
- Setting the auxiliary pedal function [AuxPedal]
- MIDI [MIDI SETTING]
- About MIDI
- Setting the MIDI transmit channel [MidiOutChannel]
- Setting the MIDI receive channel (Port A) [MidiInAChannel]
- Setting the MIDI receive channel (Port B) [MidiInAChannel]
- Setting Local control on/off [LocalControl]
- Selecting performance from the keyboard or song data for MIDI transmission [MidiOutSelect]
- Selecting a type of data received via MIDI [ReceiveParameter]
- Selecting a type of data transmitted via MIDI [TransmitParameter]
- Executing song data bulk dump [SongBulkDump]
- Transmitting the initial settings on the panel [InitialSetup]
- Executing voice data bulk dump [VoiceBulkDump]
- About MIDI
- Other settings
- Selecting a touch response [TouchResponse]
- Fine tuning the pitch [Tune]
- Selecting a tuning curve for a piano voice [PianoTuningCurve]
- Selecting a scale [Scale]
- Depth of string resonance [StringResonanceDepth]
- Depth of sustain sampling for the damper pedal [SustainSamplingDepth]
- Setting the speed of vibraphone’s vibrato effect [VibraphoneRotorSpeed]
- Selecting a pedal function for vibraphone [VibraphonePedalMode]
- Assigning the START/PAUSE function to a pedal [PedalStart/ Pause]
- Selecting a type of auxiliary pedal [AuxPedalType]
- Setting the point at which the damper pedal starts to affect the sound [HalfPedalPoint]
- Pitch bend range [PitchBendRange]
- Replacing the XG voices with preset voices [XGAlternative]
- Selecting items saved at shutdown [MemoryBackUp]
- Restoring the normal (default) settings [FactorySet]
- Other method for restoring the normal settings
- Message List
- Questions about Operations and Functions
- Troubleshooting
- Data Compatibility
- Preset Voice List
- Voice Combination Examples (Dual and Split)
- Index