Yamaha HTR-5490 - Manual (Page 70)

66
SOUND FIELD PROGRAM PARAMETER EDITING
4 Press u / d to select the
parameter.
5 Press j / i to change the
parameter value.
y
• When you set the parameter to a value other than the factory-
set value, an asterisk mark (*) appears by the parameter name
on the video monitor.
6 Repeat steps 3 to 5 above as necessary to
change other program parameters.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the parameter value you edited will
return to the factory setting. If so, edit the parameter
value again.
Resetting a Parameter to the
Factory-set Value
■ To reset some of the parameters
to the factory-set values
Select the parameter you want to reset. Then press and
hold j / i until the value temporarily stops at the factory-
set value. The asterisk mark (*) by the parameter name
disappears on the video monitor.
■ To reset all of the parameters to
the factory-set values
Use “9 PARAM. INI” on the SET MENU to reset all of
the parameter values of all DSP programs within the
selected group to the factory-set values (see page 60).
This operation resets all of the parameter values of all
DSP programs within that group to the factory-set values.
Notes
• The available parameters may be displayed on more than one
OSD page for some of the programs. To scroll through pages,
press u / d.
• You cannot change parameter values when “14 MEMORY
GUARD” on the SET MENU is set to ON. If you want to
change the parameter values, set “14 MEMORY GUARD” to
OFF (see page 62).
Changing Parameter Settings
You can enjoy good quality sound with the factory-set
parameters. Although you do not have to change the
initial settings, you can change some of the parameters to
better suit the input source or your listening room.
Adjustments should be made with the remote control.
y
• We recommended that you edit the parameter while using a
video monitor. It is easier to see the video monitor than it is to
see the front panel display.
1 Press AMP to select the
AMP mode.
2 Turn on the video monitor
and press ON SCREEN
repeatedly to select the
full display mode.
3 Select a DSP program you want to adjust.
AMP
TV VOL
PRESET PRESET
TV MUTE
TV VOL
SELECT
CH CH
+
+ –
–
TV VOL
PRESET PRESET
TV MUTE
TV VOL
SELECT
CH CH
+
+ –
–
P04 ROCK CONCERT
R O O M S I Z E … … … … 1 . 0
L I V E N E S S … … … … … … … 5
R E V . T I M E … … … … 1 . 6 s
R E V . D E L A Y … … 1 2 0 m s
R E V . L E V E L … … … … … 7 %
≥ I N I T . D L Y … … … … 1 5 m s
HALL
ENTER-
TAINMENT
TV
SPORTS
MONO
MOVIE
SELECT 6.1/ES
0 + 10
MOVIE
THEATER 1
MOVIE
THEATER 2
/DTS
SUR.
CHP/INDEX
CHURCH JAZZ CLUB
ROCK
CONCERT
3 4 2 1
5
9 10 11 12
6 7 8
ON SCREEN
DISPLAY
Program No.
Example of the parameter setting display
Parameters
Cursor
Program name
PHONO
POWER SLEEP
CLEAR LEARN
STANDBY
TRANSMIT RE–NAME
6CH INPUT SYSTEM
V-AUX
A
D-TV/LD
POWER
REC
POWER AMP
AV TV
VCR2/DVR VCR 1 DVD
SELECT
CBL/SAT MD/TAPE CD-R
TUNER CD REC
DISC SKIP
SET MENU
TV INPUT A/B/C/D/E
AUDIO
VOL
LEVEL
MENU
STEREO
HALL
ENTER- TAINMENT TV SPORTS MONO
MOVIE
SELECT 6.1/ES
0 + 10
MOVIE THEATER 1
MOVIE THEATER 2 /DTS SUR.
TEST ON SCREEN
EFFECT
CHP/INDEX
TV VOL RETURN DISPLAY
PRESET PRESET
TV MUTE
TV VOL
SELECT
CHURCH
CH CH
JAZZ CLUB ROCK CONCERT
TITLE
MUTE
+
+
+
–
–
–
3 4 2 1
5
9 10 11 12
6 7 8
2
4
5
3
1
Parameter valves
0110HTR5490_65-70_EN(UA) 01.7.6, 6:12 PM 66