Yamaha HTR-5490 - Manual (Page 25)

21
English
INTR
ODUCTION
PREP
ARA
TION
B
ASIC
OPERAIONT
AD
V
ANCED
OPERA
TION
ADDITIONAL
INFORMA
TION
APPENDIX
Selecting the OSD Mode
1 Turn on the video monitor connected to this
unit.
2 Make sure the AMP mode is selected and
press ON SCREEN on the remote control
repeatedly to change the display mode.
The OSD mode changes in the following order: full
display, short display, and display off.
Notes
• If you choose a video input source that has a component
connected to both the S VIDEO IN and composite VIDEO IN
jacks, and both the S VIDEO OUT and composite VIDEO
OUT jacks are connected to a video monitor, the video signal is
output to both the S VIDEO OUT and VIDEO OUT jacks.
However, the OSD is carried only on the S-video signal. If no
video signal is input, the OSD is carried on both the S-video
and composite video signals.
• If your video monitor is connected only to the COMPONENT
VIDEO jacks of this unit, the OSD is not shown. Make sure to
connect your video monitor to the COMPONENT VIDEO
jacks and either VIDEO or S VIDEO jacks if you want to see
the OSD.
• Playing back video software that has an anti-copy signal or
video signals with a lot of noise may produce unstable images.
P01 CONCERT HALL
R O O M S I Z E … … … … 1 . O
L I V E N E S S … … … … … … … 5
I N I T . D L Y … … … … 4 5 m s
P 0 1 C O N C E R T H A L L
PHONO
POWER SLEEP
CLEAR LEARN
STANDBY
TRANSMIT RE–NAME
6CH INPUT SYSTEM
V-AUX
A
D-TV/LD
POWER
REC
DISC SKIP
SET MENU
TV INPUT A/B/C/D/E
AUDIO
VOL
LEVEL MENU
STEREO
HALL
ENTER- TAINMENT TV SPORTS MONO
MOVIE
SELECT 6.1/ES
0 +10
MOVIE THEATER 1
MOVIE THEATER 2 /DTS SUR.
TEST ON SCREEN
EFFECT
CHP/INDEX
TV VOL RETURN DISPLAY
PRESET PRESET
TV MUTE
TV VOL
SELECT
CHURCH
CH CH
JAZZ CLUB ROCK CONCERT
TITLE MUTE
POWER AMP AV TV
VCR2/DVR VCR 1 DVD
SELECT
CBL/SAT MD/TAPE CD-R
TUNER CD
+
+
+
–
–
–
3 4 2 1
5
9 10 11 12
6 7 8
ON SCREEN
DISPLAY
ON-SCREEN DISPLAY (OSD)
You can display the operation information for this unit on
a video monitor. If you display the SET MENU and DSP
program parameter settings on a monitor, it is much easier
to see the available options and parameters than it is by
reading this information on the front panel display.
y
• If a video source is being reproduced, the OSD is
superimposed over the image.
• The OSD signal is not output to the REC OUT jack, and will
not be recorded with any video signal.
• You can set the OSD to turn on (blue background) or off when
a video source is not being reproduced (or the source
component is turned off) by using “13 DISPLAY SET” on the
SET MENU (see page 62).
OSD Modes
You can change the amount of information the OSD
shows.
Full display
This mode always shows the DSP program parameter
settings on the video monitor (see page 66).
Short display
This mode briefly shows the same contents as the front
panel display at the bottom of the screen and then
disappears.
Display off
This mode briefly shows the “DISPLAY OFF” message at
the bottom of the screen and then disappears. Afterwards,
no changes to operations appear on the monitor except
those of the ON SCREEN button.
Full display Short display
y
• When you choose the full display mode, INPUT l / h,
VOLUME and some other types of operation information are
displayed at the bottom of the screen in the same format as that
for the front panel display.
• The SET MENU and test tone display appear regardless of the
OSD mode.
0104HTR5490_19-24_EN(UA) 01.7.6, 6:11 PM 21