Panasonic DMP-BDT210 - Manual (Page 31)

Se
tti
n
g
s
31
VQT3B75
Still Mode
Select the type of picture shown when you pause playback.
Seamless Play
The chapter segments in playlists are played seamlessly.
≥ Select “On”, when the picture freezes for a moment at the
chapters segment in playlists.
NTSC Contents Output
Select PAL60 or NTSC output when playing NTSC discs.
Dynamic Range Compression
You can listen at low volumes but still hear dialog clearly.
(Dolby Digital, Dolby Digital Plus and Dolby TrueHD only)
≥ “Auto” is effective only when playing Dolby TrueHD.
Digital Audio Output
Press [OK] to show the following settings.
PCM Down Conversion
Select how to output audio with a sampling frequency of
96 kHz for the PCM output from the DIGITAL AUDIO OUT.
≥ If “On” is selected, the signals that are converted to
48 kHz are output.
≥ If “Off” is selected, and the connected equipment does not
support 96 kHz, the sound will not be output normally.
≥ Signals are converted to 48 kHz despite the settings in the
following cases:
– when the signals have a sampling frequency of 192 kHz
– when the disc has copy protection
– when “BD-Video Secondary Audio” is set to “On”
Downmix
Select the downmix system of multi-channel to 2-channel
sound.
≥ Select “Surround encoded”, when the connected
equipment supports the virtual surround function.
≥ There is no effect on “Bitstream” via HDMI AV OUT and
DIGITAL AUDIO OUT.
≥ The audio will be output in “Stereo” in the following cases:
– AVCHD playback
– Playback of secondary audio (including the button click
sound).
7.1ch Audio Reformatting [BDT310] [BDT210]
Surround sound with 6.1ch or less is automatically
expanded and played back at 7.1ch.
≥ If “Off” is selected, sound is played over the original
number of channels.
(Note that in the case of 6.1ch audio, playback will be at
5.1ch.)
≥ Audio reformatting is enabled in the following cases:
– When you have selected “PCM” in “Digital Audio
Output”.
– When the audio is Dolby Digital, Dolby Digital Plus,
Dolby TrueHD or LPCM.
– BD-Video playback
High Clarity Sound [BDT310] [BDT210]
When connected to TV via the HDMI terminal for outputting
image, it produces clearer sound.
≥ Set to “Enable” and then set “High Clarity Sound” on the
Playback menu to “On”. (> 29)
Audio Delay
Synchronization between picture and sound is corrected by
adjusting the delay time of the audio output.
Picture
Automatic
Automatically selects the type of picture
shown.
Field
Select if jittering occurs when “Automatic”
is selected.
Frame
Select if small text or fine patterns cannot
be seen clearly when “Automatic” is
selected.
Sound
Dolby D/Dolby D +/Dolby TrueHD
DTS/DTS-HD
MPEG Audio
Select the audio signal to output.
≥ Select “PCM”, when the connected equipment cannot
decode the respective audio format. This unit decodes
the audio format and transmits to the connected
equipment.
≥ Not making the proper settings may result in noise.
BD-Video Secondary Audio
Select whether to mix or not mix the primary audio and
secondary audio (including the button click sound). (> 19)
≥ If “Off” is selected, the unit outputs the primary audio only.
DMP-BDT310_110EB-VQT3B75.book 31 ページ ２０１１年２月２１日 月曜日 午後５時１７分