VIEWSONIC VS12476 User Manual

Viewsonic, Pjd6531w dlp projector

ViewSonic

IMPORTANT: Please read this User Guide to obtain important information on install-

ing and using your product in a safe manner, as well as registering your product for

future service. Warranty information contained in this User Guide will describe your

limited coverage from ViewSonic Corporation, which is also found on our web site

at http://www.viewsonic.com in English, or in specific languages using the Regional

selection box in the upper right corner of our website.

“Antes de operar su equipo lea cuidadosamente las instrucciones en este manual”

Model No. : VS12476

- User Guide

- Guide de l’utilisateur

- Bedienungsanleitung

- Guía del usuario

- Guida dell’utente

- Guia do usuário

- Användarhandbok

- Käyttöopas

- Руководство пользователя

- 使用手冊 (繁體)

- 使用手冊 (簡體)

- 사용자 안내서

- คู่มือการใช้งาน

- Podręcznik użytkownika

- Kullanιcι kιlavuzu

PJD6531w

DLP Projector

Table of contents

Document Outline

VPD-W5600-EN.pdf
- FCC Notice
- Safety Instructions
- Notes on the AC Power Cord
  - Introduction
    - Projector Features
    - Package Contents
  - Projector with Lens Cap
  - AC Power Cord
    - Projector Overview
  - Using the Product
    - Control Panel
    - Connection Ports
    - Remote Control
    - Installing the Batteries
      - 1. Open the battery cover in the direction shown.
      - 2. Install batteries as indicated by the diagram inside the compartment.
      - 3. Close the battery cover into position.
    - Remote Control Operation
  - Installation
    - Connecting the Projector
    - Powering On/Off the Projector
- Powering On the Projector:
  - 1. Remove the projector lens cap.
  - 2. Complete the AC power cord and peripheral signal cable(s) connections.
  - 3. Press button to turn on the projector. The projector takes a minute or so to warm up.
  - 4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
- Powering Off the Projector:
  - 1. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.
  - 2. Press button again to confirm.
  - 3. Disconnect the AC power cord from the electrical outlet and the projector.
  - 4. Do not turn on the projector right after power off.
  - Adjusting the Projector
- Adjusting the Projector Height
  - 1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.
  - 2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.
- Adjusting the Projector Zoom and Focus
  - 1. Focus the image by rotating the focus ring. A still image is recommended for focusing.
  - 2. Adjust the image by sliding the zoom ring.
- Adjusting Projection Image Size
  - Menu Operation
    - 1. Press the MENU button to open the OSD menu.
    - 2. When OSD is displayed, use p / q to select any feature in the main menu.
    - 3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.
    - 4. Use p / q to select the desired item and adjust the settings with t / u.
    - 5. Press the MENU button, the screen will return to the main menu.
    - 6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.
  - Network Control
    - 1. Connect one end of the internet cable to the Network Control connector on the projector.
    - 2. Connect the other end of the internet cable to an available RJ-45 connector on your computer.
    - 3. Turn on your projector and computer.
    - 1. Enable DHCP from the projector OSD, under Network Config.
    - 2. Start browser in PC and specify following URL, then click “Go” button.
    - 3. If connection succeeds, the login screen is displayed. Enter your User name and Password and click “OK”. Below are the factory default settings for administrator, user and passwords.
    - 1. Set IP Address and Subnet Mask under Network Config.
    - 2. From your computer, go to Start > Settings > Network and Dial-up Connections > Local Area Connection and right click to select Properties..
    - 3. Select "Intel Protocol (TCP/IP)" and click "Properties".
    - 4. Set your PC’s IP address, and click OK.
    - 5. Start browser in PC and specify following URL, then click “Go” button.
    - 6. If connection succeeds, the login screen is displayed. Enter your User name and Password and click “OK”. Below are the factory default settings for administrator, user and passwords.
    - 1. Go to Tools > General and click "Settings".
    - 2. Click "Every visit to the page" and "OK".
    - 3. Click "OK" to exit "Internet Properties".
  - Maintenance
    - Cleaning the Lens
    - Cleaning the Projector Housing
    - Cleaning the Filter Cover
      - 1. Switch the projector off and unplug the AC power cord from the wall socket.
      - 2. Remove the filter cover as the illustration shown.
      - 3. Clean the filter cover.
      - 4. Replace the filter cover.
      - 5. Attach the filter cover.
      - 6. Plug the power back into the projector.
    - Replacing the Lamp
      - 1. Turn off the projector.
      - 2. If the projector is installed in a ceiling mount, remove it
      - 3. Unplug the power cord.
      - 4. Loosen the screw in the side of the lamp cover and remove the cover.
      - 5. Remove the screws from the lamp module, raise the handle, and lift out the module.
      - 6. Insert the new lamp module into the projector and tighten the screws.
      - 7. Replace the lamp cover and tighten the screw.
      - 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.
      - 9. Reset the lamp hour. Refer to the “Setting” menu.
  - Specifications
  - Appendix
    - LED Indicator Messages
    - Compatibility Modes
- Computer:
- Video:
  - Troubleshooting
- Start-up problems
- Image problems
  - RS-232 Command and Configuration
  - IR Control Code