Vox Valvetronix ToneLab SE - Manual (Page 51)

AMP TYPE
CABINET
TYPE
PEDAL
MODULA
TION
DELA
Y
REVERB
Amp/Effect
41
4. BI CHORUS M
ONO
I
N
/M
ONO
O
UT
1 (M
ODE
=S) S
TEREO
I
N
/
S TEREO O UT 1 (M ODE =P1, P2, P3)
This is a chorus model unique to ToneLabSE. It provides two chorus units, CHO-
RUS 1 and CHORUS 2, and lets you connect the two units not only in series or in
parallel, but also to synchronize or de-synchronize the two LFOs. It produces a
variety of tones that cover a range from wonderfully spacious sounds to bizarre
flanger-like sounds with complex modulation.
5. DUO PHASE (DUO PHAS) M
ONO
I
N
/M
ONO
O
UT
2 (M
ODE
=S1,
S2) S
TEREO
I
N
/S
TEREO
O
UT
2 (M
ODE
=P1, P2, P3)
This is an amazing phaser that provides two six-stage phasers; PHASER 1 and
PHASER 2. They can be connected in series (to make a pseudo-twelve-stage
phaser!) or in parallel, and you can also synchronize or de-synchronize the two
LFOs.
[6] “MIX” 0.0–10.0 * Adjusts the mix amount of the effect sound.
CONTROL pedal If you set the FLN TRIG: CONTROL pedal setting
to “FLN TRIG,” the LFO will be reset to the posi-
tion specified by OFFSET whenever you operate
the pedal. (p.56 Control pedal settings)
[1] “SPEED 1” 0.100–10.00 [Hz] * Adjusts the modulation speed of CHORUS 1.
[2] “DEPTH”
0.0–10.00 * Adjusts the modulation depth of CHORUS 1/2.
[3] “RESO” 0.0–10.0 * Adjusts the amount of resonance for CHORUS
1/2.
[4] “SPEED 2” 0.100–10.00 [Hz] * Adjusts the modulation speed of CHORUS 2.
NOTE: This will not function if MODE is set to P2 or P3.
[5] “MODE” S/P1/P2/P3 Specifies the connection and LFO for CHORUS
1/2.
S: CHORUS 1/2 are connected in series.
P1: CHORUS 1/2 are connected in parallel.
P2: CHORUS 1/2 are connected in parallel, and
their LFOs are synchronized.
P3: CHORUS 1/2 are connected in parallel, and
their LFOs are synchronized in opposite
phase (Stereo mode).
NOTE: If P2 or P3 is selected, the speed is adjusted by the SPEED 1
knob.
[6] “MIX” 0.0–10.0 * Adjusts the mix amount of the effect sound.
[1] “SPEED 1” 0.100–10.00 [Hz] * Adjusts the modulation speed of PHASER 1.
[2] “DEPTH”
0.0–10.0 * Adjusts the modulation depth of PHASER 1/2.
[3] “RESO” 0.0–10.0 * Adjusts the amount of resonance for PHASER
1/2.
[4] “SPEED 2” 0.100–10.00 [Hz] * Adjusts the modulation speed of PHASER 2.
NOTE: This will not function if MODE is set to S2, P2, or P3.