Tyco Digital Security Control PC158O - Manual (Page 8)

The Liquid Crystal Display (LCD) displays prompts and
system information on two 16 character lines.
If “< >” appears, more information can be accessed by
using the arrow (< >) keys. Press
[<] to see the previous
function or item of information. Press [>] to advance the
display to next function or item of information.
Press the keys on the number pad as prompted by the
LCD display to view alarms or troubles, to arm and
disarm the system and to bypass zones.
To exit a function and return to the Ready state, press [#].
To select a function press [ ✱ ].
LCD5500 Keypad PC5506 LED Keypad
Ready Light (All keypads) :
If the Ready light is ON, the system is ready for arming.
The system cannot be armed unless the Ready light is
ON (see “Arming the System” on page 3).
Armed Light (All keypads) :
If the Armed light is ON, the system has been armed
successfully.
Trouble Light (All keypads) :
If the Trouble light is ON, see “Viewing Trouble
Conditions” on page 11.
Memory Light (LED keypads only):
Upon disarming, if an alarm has occurred while the
system was armed, the Memory light will turn ON (See
“Disarming the System” on page 5).
Display Lights
Ready Armed Trouble
Away
Reset
Chime
Exit
Stay
< >
Message Display Security Station
Press to select function.
Press to Exit / Return.
Indicates more information is
available. Press either key to view.
Press to advance display to the
next function or message.
Press to see previous function or message.
TEST SYSTEM WEEKLY
Refer to Instruction
Manual for testing
instructions.
NOT IN USE NOT IN USE NOT IN USE
Enter Code
To Arm System
Ready Armed Trouble
Memor y
Fire
Bypass Bypass
Program
6 5 4 3 2 1 6 5 4 3 2 1
Away
Reset
Chime
Exit
Stay
1
2
3
4
5
6
TEST SYSTEM WEEKLY
Refer to Instruction Manual for
testing instructions.
NOT IN USE NOT IN USE NOT IN USE
PC1575RK LED Keypad
Emergency Keys (All Keypads)
PC5506 / LCD5500:
Press both * Keys for two seconds to send a FIRE
transmission.
Press both * Keys for two seconds to send an
AUXILIARY transmission.
Press both * Keys for two seconds to send a PANIC
transmission.
PC1575RK / SL-75:
Press the [F]* key for two seconds to send a FIRE
transmission.
Press the [A]* key for two seconds to send an
AUXILIARY transmission.
Press the [P]* key for two seconds to send a PANIC
transmission.
* IMPORTANT NOTE (All Keypads): The Fire,
Auxiliary and Panic keys will NOT function unless
programmed by the installer. If these keys are in
service and the installer has enabled audible
feedback, holding down the key for two seconds
will cause the keypad sounder to beep indicating
that the input has been accepted and transmission
is underway.
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Bypass
Trouble
Armed
Memory
Ready
F A P
4
7
2
5
8
0
3
6
9
#
1
1
2
3
4
5
6
ZONE BYPASSING:
PROGRAMMING USER CODES:
INSTANT ARM:
Press [ ] [1] [Zone
to be bypassed]. Press [#] to return to
“Ready”. Arm the system.
Press
[ ] [5] [Master Code] [1 to 6 for user
code number]. Enter four digits. Press
[#] to return to “Ready”.
Press [ ] [9] [User
Code] to arm the system without entry
delay.
Θ
Θ
Θ
F P A
NOT
IN
USE
NOT
IN
USE
NOT
IN
USE
TEST SYSTEM WEEKLY
18000031 R3
Important Note: Test system weekly and
have any system trouble conditions
corrected by your alarm installer.
SL-75 LED Keypad
Bypass Light (LED keypads only):
If the Bypass light is ON, one or more zones are
bypassed (See “Zone Bypassing”
on page 10).
Fire Light (PC5506 keypad only):
If the Fire light is ON, a fire alarm has occurred (See
“Fire Alarm Operation” on page 13).
Program Light (PC5506 keypad only):
The Program light will flash when you are
programming access codes, or performing other
programming functions. If someone is programming
at another keypad, the Program light will turn ON to
indicate that the system is busy.
System Light (SL-75
Only):
If the System light is
ON, the system is busy
and one or more of the
conditions could be
present:
System Troubles (See
“Viewing Trouble
Conditions” on page 9).
Alarm Memory (See
“Disarming the System”
on page 5).
Zone Bypassing (See
“Zone Bypassing”
on
page 8).
NOTE: If you have a SL-75 keypad, the System
light acts as a Trouble, Memory and Bypass
indicator. Unlike the other keypads, these
conditions will only be represented by the System
light. Please keep this in mind when reading other
functions in this manual.
9 8
2
5
8
3
6
9
# 0
4
7
F A P
1
1
5
2
6
3 4
Ready Armed System
✱
ST
AY
RE
SE
T
AW
AY
EX
IT
CH
IM
E
✱