Toshiba B-480-QQ - Manual (Page 9)

E2-3
2. SPECIFICATIONS EO1-33008
2.4 Media
NOTES: 1. The media specification other than above are unchanged.
2. The label length must be satisfied by the following conditions in each case.
(*1) When issuing a label using the rotary cutter, printing at a speed of 3"/sec., label length should be:
91.0mm - (Gap length/2) or more
(*2) When issuing a label using the rotary cutter, printing at a speed of 4"/sec., label length should be:
95.0mm - (Gap length/2) or more
(*3) When issuing a label using the rotary cutter, printing at a speed of 5"/sec., label length should be:
99.0mm - (Gap length/2) or more
(*4) When issuing a label using the rotary cutter, printing at a speed of 8"/sec., label length should be:
110.0mm - (Gap length/2) or more
(*5) When issuing a label using the swing cutter, label length should be:
35.0mm - (Gap length/2)
I I
H H
G
G
D
C
C
1
1
2
2
A A
F
B
E
Stop
position
Cut
position
Label
Reference
coordinate
Reference
coordinate
Stop
position
Cut
position
Feed direction
Tag paper
Black Mark
(on reverse side)
Tag paper
Reference
coordinate
Reference
coordinate
F
Refer to the following
NOTE 2. Black Mark
(on reverse side) 2.4 Media
Fig. 2-1
Item
A : Span of one label/tag
Label dispensing mode
Rotary cutter
3"/sec.:30.0
4"/sec.:30.0
5"/sec.:30.0
8"/sec.:38.0
2730.0
50.8
112.0
47.8
109.0
20.0
2726.0
2.0
10.0
10.0
1.0
1361.0
104.0 0.2
2730.0
2724.0
Cut mode
[Unit: mm]
Swing cutter
Head-up is OFF Head-up is ON
3"/sec.:94.0 3"/sec.:38.0
4"/sec.:98.0 4"/sec.:38.0
5"/sec.:102.0 5"/sec.:38.0
8"/sec.:113.0 8"/sec.:38.0
3"/sec.:81.0(*1) 3"/sec.:25.0
4"/sec.:85.0(*2) 4"/sec.:25.0
5"/sec.:89.0(*3) 5"/sec.:25.0
8"/sec.:100.0(*4) 8"/sec.:25.0
Strip mode Batch mode
25.4
-
10.0 Min.
Label
Max.
Min.
Max.
Min.
Max.
Max.
Min.
38.0
25.4
25.0 (*5)
- 10.0
3"/sec.:28.0
4"/sec.:28.0
5"/sec.:28.0
8"/sec.:36.0
23.0 - 8.0
2730.0
- 2726.0
Tag
23.4 8.0
3"/sec.:79.0 3"/sec.:23.0
4"/sec.:83.0 4"/sec.:23.0
5"/sec.:87.0 5"/sec.:23.0
8"/sec.:98.0 8"/sec.:23.0
23.0 21.4 6.0
2728.0
6.0
2726.0
2.0
H : Effective print length
Min.
Label
Max.
Min.
Max.
Tag
I : Print speed up/slow down area
Maximum effective length for on the fly issue
Outer roll diameter
B : Label/tag length
C : Width including backing paper
Max.
Min.
D : Label width
Max.
Min.
E : Gap length
Max.
Min.
F : Black mark length (Tag paper)
Tag
Label
Thickness
Max.
Min.
G : Effective print width