Onkyo HT-S7300 User Manual

Page 67

■

There’s no sound

■

There’s no video

■

The AV receiver’s remote controller doesn’t
control your iPod

■

The AV receiver unexpectedly selects your iPod
as the input source

■

Can’t record

■

There’s no sound

■

The Zone 2 speakers produce no sound

■

The sound changes when I connect my
headphones

■

The speaker distance cannot be set as required

■

How do I change the language of a multiplex
source

■

The

functions don’t work

■

The functions System On/Auto Power On and
Direct Change don’t work for components
connected via

■

When performing “Audyssey 2EQ

Room

Correction and Speaker Setup”, the
measurement fails showing the message
“Ambient noise is too high.”.

To control an Onkyo component that’s not connected
via

, point the remote controller at the compo-

nent. Be sure to enter the appropriate remote control
code first.

The entered remote control code may not be correct.
If more than one code is listed, try each one.

—

UP-A1 Dock for iPod

Make sure your iPod is actually playing.

—

Make sure your iPod is inserted properly in the
Dock.

—

Make sure the UP-A1 Dock is connected to the UNI-
VERSAL PORT jack on the AV receiver.

—

Make sure the AV receiver is turned on, the correct
input source is selected, and the volume is turned up.

—

Make sure the plugs are pushed in all the way.

—

Try resetting your iPod.

—

Make sure that your iPod model’s TV OUT setting is
set to On.

—

Make sure the correct input is selected on your TV or
the AV receiver.

—

Some versions of the iPod do not output video.

—

Make sure your iPod is properly inserted in the
Dock. If your iPod is in a case, it may not connect
properly to the Dock. Always remove your iPod
from the case before inserting it into the Dock.

—

The iPod cannot be operated while it’s displaying the
Apple logo.

—

Make sure you’ve selected the right remote mode.

—

When you use the AV receiver’s remote controller,
point it toward your AV receiver.

—

When connecting UP-A1 Dock to the radio tuner
UP-HT1 with AUTO selected by the tuner’s Mode
Selector switch, you can switch the input source
between UP-A1 Dock and the tuner, by pressing
PORT repeatedly on the front panel.

—

If you still can’t control your iPod, start playback by
pressing your iPod model’s Play button. Remote
operation should then be possible.

—

Try resetting your iPod.

—

Depending on your iPod, some buttons may not
work as expected.

—

Always pause iPod playback before selecting a dif-
ferent input source. If playback is not paused, the
Direct Change function may select your iPod as the
input source by mistake during the transition
between tracks.

—

Recording

On your recorder, make sure the correct input is
selected.

—

To prevent signal loops and damage to the AV
receiver, input signals are not fed through to outputs
with the same name (VCR/DVR IN to VCR/DVR
OUT).

—

Zone 2

Only components connected to analog inputs can be
played in Zone 2.

—

To use the Zone 2 speakers, you must set the “Front
High/Zone2” setting to “Zone2” .

Others

When a pair of headphones is connected, the listen-
ing mode is set to Stereo, unless it’s already set to
Stereo, Mono or Direct.

—

In some cases, corrected values suitable for home
theater use may be set automatically.

—

Use the “Multiplex” setting on the “Audio Adjust”
menu to select “Main” or “Sub”.

To use

, you must make an

connection and an

analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected dig-
itally.

These functions don’t work when Zone 2 is turned
on.

This can be caused by any malfunction in your
speaker unit. Check if the unit produces normal
sounds.

—