Onkyo HT-S7300 - Manual (Page 40)

40
En
Component Video Input
If you connect a video component to a component video
input, you must assign that input to an input selector. For
example, if you connect your Blu-ray Disc/DVD player to
COMPONENT VIDEO IN 2, you must assign “IN2” to
the “BD/DVD” input selector.
Here are the default assignments.
■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,
TV/CD, PORT
`
IN1, IN2:
Select a corresponding component video input that
the video component has been connected.
` - - - - -:
Select if you are using HDMI output, not component
video output, to output composite video and compo-
nent video sources.
Note
• If you connect a component (such as UP-A1 Dock that seated
iPod) to the UNIVERSAL PORT jack, you cannot assign any
input to “PORT” selector.
Digital Audio Input
If you connect a component to a digital audio input, you
must assign that input to an input selector. For example, if
you connect your CD player to the OPTICAL IN 1, you
must assign “OPT1” to the “TV/CD” input selector.
Here are the default assignments.
■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,
TV/CD, PORT
` COAX1, COAX2, OPT1, OPT2:
Select a corresponding digital audio input that the
component has been connected.
` - - - - -:
Select if the component is connected to an analog
audio input.
Note
• When an HDMI IN is assigned to an input selector in
“HDMI Input” ( ➔ 39), the same HDMI IN will be set as a prior-
ity in this assignment. In this case, if you want to use the coaxial
or optical audio input, make the selection in the Audio Selector
in the Audio menu.
• Available sampling rate for PCM signals from a digital input
(optical and coaxial) is 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.
• If you connect a component (such as UP-A1 Dock that seated
iPod) to the UNIVERSAL PORT jack, you cannot assign any
input to “PORT” selector.
Main menu Speaker Setup
Here you can check the settings made by Audyssey 2EQ
Room Correction and Speaker Setup function, or set them
manually, which is useful if you change one of the con-
nected speakers after using Audyssey 2EQ Room Correc-
tion and Speaker Setup function.
Note
• These settings are disabled when:
– a pair of headphones is connected, or
– the “Audio TV Out” setting is set to “On” (
➔ 49) and an
input selector other than HDMI is selected.
Speaker Settings
■ Speaker Terminal Assign
Front High/Zone2
With this setting, you can specify the speakers con-
nected to FRONT HIGH OR ZONE 2 SPEAKERS
terminals.
` Front High:
Front high speakers can be used.
` Zone2:
Zone 2 speakers can be used (Powered Zone 2
enabled).
SurrBack/Front High
With this setting, you can specify the speakers con-
nected to SURR BACK OR FRONT HIGH SPEAK-
ERS terminals.
` Surr Back:
Surround back speakers can be used.
` Front High:
Front high speakers can be used.
Note
• If “Front High” is selected in the “Front High/Zone2” setting,
you cannot select “Front High” here.
Input selector Default assignment
BD/DVD IN1
VCR/DVR - - - - -
CBL/SAT IN2
GAME - - - - -
AUX - - - - -
TUNER - - - - - (Fixed)
TV/CD - - - - -
PORT - - - - -
Input selector Default assignment
BD/DVD COAX1
VCR/DVR - - - - -
CBL/SAT COAX2
GAME OPT1
AUX - - - - -
TUNER - - - - - (Fixed)
TV/CD OPT2
PORT - - - - -
Speaker Setup
Some of the settings in this section are set automatically
by Audyssey 2EQ
® Room Correction and Speaker
Setup function (
➔ 28).
If you change these settings, you must run
Audyssey 2EQ Room Correction and Speaker Setup
again (
➔ 28).