One for All URC 4080 - Manual (Page 9)

6. Write your TV/VCR Combo code in the boxes
below for future reference.
NOTE: Remember, to use the One For All 4-Device Video Expert
to operate your TV/VCR Combo, press VCR first.
Setup Codes for TV/VCR Combos:
Brocksonic 0002, 0479 (TV:0463)
Citizen 0278
Colt 0072
Curtis Mathes 0035 (TV:0051)
Daewoo 0278 (TV:0624)
Emerson 0002, 0479 (TV:0463), 0278 (TV:0624)
Funai 0000
GE 0060 (TV:0047), 0048 (TV:0093), 0035 (TV:0051), 0240
GoldStar 0037 (TV:0056)
Harley Davidson 0000
Hitachi 0000
Lloyd's 0000
Magnasonic 0278
Magnavox 0000, 0081 (TV:0054)
Magnin 0240
Memorex 1162, 1262, 0162 (TV:0250), 0037 (TV:0056), 1037
MGA 0240
Mitsubishi 0048 (TV:0093)
Optimus 1162, 1262, 0162 (TV:0250)
Orion 0002, 0479 (TV:0463)
Panasonic 1162, 1262, 0162 (TV:0250), 0035 (TV:0051)
Penney 0037 (TV:0056), 0035 (TV:0051), 0240
Quasar 0162 (TV:0250) , 0035 (TV:0051)
Radio Shack 1037
RCA 0060 (TV:0047), 0048 (TV:0093), 0035 (TV:0051), 0240
Sansui 0000, 0479 (TV:0463)
Sanyo 0240
Sears 0000, 0037 (TV:0056)
Sharp 0048 (TV:0093)
Sony 0032 (TV:0000)
Sylvania 0081 (TV:0054)
Symphonic 0000
Thomas 0000
White Westinghouse 0278 (TV:0624)
Zenith 0000, 0479 (TV:0463)
17
PROGRAMMING TV/VCR COMBO CONTROL
Locate the brand name of your TV/VCR Combo in the
Setup Codes For TV/VCR Combos section on the next page,
and write it in the following space.
TV/VCR Combo Brand: ________________________
The brands are listed in alphabetical order with the most
popular codes listed first. To program TV/VCR control:
1. Turn on your TV/VCR Combo and insert a
video cassette.
2. On the remote control, press VCR once. Press
and hold SET until the LED blinks twice, then
release SET.
NOTE: The remote control will exit programming if
more than 10 seconds elapse between key presses.
3. Enter the first four-digit code for your TV/VCR
Combo. If you perform this procedure correctly,
the LED will blink twice.
NOTE: If the LED emits a long blink, the code is
invalid. Repeat steps 2 through 3 and try entering the
same code again.
4. Aim the remote control at your TV/VCR Combo
and press POWER once. The unit should turn
off. If it does not respond, repeat steps 2-3, try-
ing each code listed for your brand until you
find one that works. If it still does not work, try
searching for the code (see Searching For Your
Code on page 23).
5. If you’ve located a TV/VCR setup code that
works your TV/VCR Combo and a separate TV
code is also listed, you’ll need to program this
code into the remote control to access volume
control (see Programming TV Control on page 8).
If there is no separate TV code listed, you will
need to perform the following steps to access
volume control:
a. Press and hold SET until the LED blinks
twice, then release SET.
b. Enter 9 - 9 - 3. The LED will blink twice.
c. Press VCR once. The LED will blink twice.
16