Outlaw Audio 990 User Manual
Page 42
42
Outlaw Audio
Owner’s Manual
43
Model 990 7.1 Channel Preamp/Processor
Owner’s Manual
Remote Control Setup and Operation
Checking the Codes
If you have set up the Model 990 remote by searching for the codes, for future
reference, you may wish to find out which four-digit code is operating your
equipment.
To find the four-digit code for a device:
1. On the Model 990 remote, press the button near the top of the
remote for the type of device you want to control.
2. Press and hold SETUP until the red LED on the remote blinks twice,
then release SETUP.
3. Enter 990.
The LED will blink twice.
4. To view the code for the first digit, press 1.
After three seconds, the LED will blink to indicate the first code number
(i.e., 3 blinks = 3). Count the blinks and write down the number.
5. Repeat step for each of the other three digits. Press 2 for the second
digit, 3 for the third, and 4 for the fourth. Count the blinks and write
down the numbers.
6. To check for the codes of your other components, repeat steps 1
through 5, but substitute the appropriate key in step 1 for the new
component you are checking.
Re-Assigning Device Buttons
If you wish to control a second device of a type already programmed into the
Model 990 remote (i.e., if you want to use two DVD players), you will need to
re-assign an unused device button (CBL, AUX, VCR, TV, SAT, CD, or AMP) to
operate the second device.
To reassign an unused device button:
1. On the Model 990 remote, press and hold SETUP until the LED
blinks twice, then release SETUP.
2. Enter 992.
The LED will blink twice.
3. Press the button for the device already programmed (i.e., CBL),
then press the button for the unused device (i.e., TV).
The LED will blink twice.
4. The button for the unused device is now ready to be programmed for
the second component. See Setup Using Preprogrammed Codes.
Volume Control Punch-Through
You can program the Model 990 remote so that the VOLUME UP, VOLUME
DOWN, and MUTE buttons on the remote will control those functions on the
Model 990 even when the remote is set to control another device.
To set volume control punch-through:
1. On the Model 990 remote, press and hold SETUP until the LED
blinks twice, then release SETUP.
2. Enter 993.
3. Press the TNR key on the Model 990 remote.
The LED will blink twice.
Operation
After you have programmed the remote control for your equipment, use the
following procedures to operate the components of your home entertainment
system:
To operate a system component that you have programmed:
1. On the Model 990 remote, press the button near the top of the
remote for the device you want to control (CBL, AUX, VCR, TV, SAT,
CD, or AMP)
2. Aim the remote control at the device and press the POWER button
to turn on the device.
3. Press the buttons that send out the commands you desire.
NOTE: Some audio/video devices have separate buttons for POWER
ON and POWER OFF. To operate these devices on the remote, press the
corresponding device button to turn the equipment ON and press the
POWER button to turn the equipment OFF.
Please try all the functions of this remote control with your equipment. The most
common functions are labeled on the remote. However, some of the secondary
functions might be stored under a button that has a different name from the
one on your original remote control.
Source Selection Buttons
Pressing a source button (VIDEO 1, DVD, etc.) at the bottom of the remote
control performs the following functions:
If the Model 990 is in Standby mode, powers up the unit.
Selects that source on the Model 990.
Backlighting
Pressing any button on the Model 990 remote illuminates all the buttons on
the remote control for about 5 seconds. The backlight is extended an additional
5 seconds with any button press while the backlight is on.