Onkyo TX-SE550 - Manual (Page 25)

25
Using preset radio stations
GROUP
Number buttons
GROUP √ PRESET ®
TUNER
SCAN
FM MUTE/MODE
MEMORY
BASS TREBLE
C D PHONES
Re-EQ
A/V KARAOKE CONTROL RECEIVER TX-SE550
AM FM DVD PHONO 1 VIDEO 2 VIDEO TI CH INPUT MUL TAPE( ) MONITOR
CLEAR
MEMORY FM MUTE / MODE SPEAKERS A B MIDNIGHT THEATER SURROUND MODE
MASTER VOLUME
OFF ON
POWER
STANDBY/ON
ECHO LEVEL
3-D BASS
MIC LEVEL
KARAOKE
MIC 1 2
1
MAX MIN
2
MAX MIN MAX MIN
KEY CONTROL VOCAL CANCEL SCAN GROUP DIRECT TUNING
STANDBY
1 2 3 4 5 6 7 8 9 0 /10 TUNING PARAMETER CONTROLLER
PARAMETER SELECTOR
AM
FM
POWER SLEEP
DVD VIDEO-1 VIDEO-2
TAPE PHONO C D LEARN
INPUT SELECTOR
DVD
KARAOKE
VOCAL CANCEL
KEY CONTROL
DISC
GROUP
VOLUME
TAPE
DIMMER
TUNER
POWER
POWER
VOLUME C H
TV/VCR
MUTING
LEVEL
REMOTE CONTROLLER
CH SEL
TEST TONE
SENDING/ LEARNED
PRESET
PROGRAMMABLE AREA TV/VIDEO
TUNER
CD
MULTI-CH INPUT
RC-386M
SUR MODE
1. Select the frequency that you want to store in the memory.
(See Tuning in a radio station on page 24.)
2. Press the MEMORY button.
The MEMORY indicator will light up for eight seconds.
3. While the MEMORY indicator is lit, press the GROUP but-
ton to choose the desired group.
The group shown on the display changes in the following order
each time the button is pressed:
4. Select the desired memory number using number buttons.
•
Since ten AM or FM stations can be stored in each group (A, B
or C), a total of 30 stations can be stored in the memory.
1. Select the tuner as the source by pressing the AM or FM
input selector button on the main unit.
2. Press the GROUP button until the desired group is dis-
played.
3. Enter the desired preset number using the number buttons
or press the SCAN button to scan through the preset sta-
tions.
If the SCAN button is pressed, each station stored in the
selected group will be played for five seconds. When the desired
station is found, press the SCAN button again to stop scanning.
Remote controller operation
1. Select the tuner as the source by pressing the TUNER input
selector button on the remote controller.
2. Press the GROUP button until the desired group is displayed.
3. Press the PRESET (√ or ®) button.
1. Select the preset station you wish to remove as explained in
the previous section.
2. Press the FM MUTE/MODE button while holding down the
MEMORY button. “– –” appears on the channel display.
•
Once the preset station has been cancelled, the memory location
can be used to store another station.
Programming radio stations
Selecting a preset station
Cancelling preset stations
GROUP A GROUP B GROUP C
SPEAKERS A GROUP FM STEREO
B
CH MHz
VIDEO 2
TUNED FM MUTE
1 2 3 4 5 6 7 8 9 0 /10
SPEAKERS A GROUP FM STEREO
A
CH MHz
VIDEO 2
TUNED FM MUTE
MEMORY
CLEAR
MEMORY FM MUTE / MODE
GROUP SPEAKERS A FM STEREO
B
CH MHz
VIDEO 2
TUNED FM MUTE
MEMORY
SCAN GROUP
2
3
4
SCAN GROUP
Remote controller
GROUP
AM FM
Remote controller
TUNER
1
2
3
SCAN GROUP
Remote controller
PRESET
or
1 2 3 4 5 6 7 8 9 0 /10
CLEAR
MEMORY FM MUTE / MODE SPEAKERS A GROUP FM STEREO
B
CH MHz
VIDEO 2
TUNED FM MUTE