Onkyo TX-NR900E - Manual (Page 40)

40
To record the input source signal you are
currently watching or listening to
This method outputs to the audio and video outputs the currently
selected input source signal. This method allows you to a signal
while you are actually listening to or watching it.
1. Select the input source to record by pressing the
corresponding input source button.
The input source is now selected and you may watch or listen to
it as desired.
2. Press the REC OUT button repeatedly until “Rec
Sel:SOURCE” appears in the front display.
The signal from the currently selected input source is now output
to the TAPE OUT, VIDEO 1 OUT, VIDEO 2 OUT outputs for
recording.
3. Start recording at the recording component as
desired.
To confirm the settings, press the REC OUT button. The current
settings will appear for 8 seconds in the front display.
Notes:
• If you change the input source during recording, you will record
the signals from the newly selected input source.
• You cannot record the surround effects.
• Digital signals input to the DIGITAL INPUT (COAX) and
DIGITAL INPUT (OPT) inputs will be output to the DIGITAL
OUTPUT (OPT) output. However, MP3, WMA, WAV, and
other music formats played using Net Audio are only output as
analog audio.
• Digital input signals are only output to the digital outputs and
analog input signals are only output from the analog outputs.
There is no conversion from digital to analog or vice versa.
When connecting CD players and other digital components, do
not connect only the digital terminals, but the analog ones as
well.
• There are some restrictions on recording digital signals. When
making digital recordings, consult the instruction manual that
came with your digital recording equipment (e.g., MD recorder
or DAT deck) to know what restrictions are imposed.
• You cannot record the source connected to the MULTI
CHANNEL INPUT connector.
Recording a source
Input source buttons
STANDBY/ON
STANDBY
DVD ZONE 2 ( ) GRN REC ( ) RED AUDIO SELECTOR PURE AUDIO UPSAMPLING
OFF ON
POWER
MASTER VOLUME
TUNER PHONO NET AUDIO C D TAPE VIDEO 3 VIDEO 5 VIDEO 4 VIDEO 2 VIDEO 1
VCR 2 VCR 1
DISPL AY
STEREO SURROUND THX DSP REC OUT ZONE 2 OFF RT/ PTY/ TP MEMORY FM MODE SETUP ENTER RETURN
S VIDEO AUDIO VIDEO L R DIGITAL
VIDEO 5 INPUT
PRESET TUNING CLEAR ZONE 2 LEVEL
PHONES
REC OUT
• When listening to music in the remote zone (see previous page),
you can record the music or video that is being played in the
main zone.
• If you select FM (or AM) with the TUNER input source button
when the recording source is set to AM (or FM), the output for
the recording source also changes to AM (or FM).
To record an input source signal different from
that you are currently watching or listening to
Follow the procedure given below to record an input source signal
different from that which you are listening to or watching at the time
of recording.
1. Press the REC OUT button.
2. Within 8 seconds, press the input source selector button
of the input source signal that you wish to record.
The signal from the selected input source is now output to the
TAPE OUT, VIDEO 1 OUT, and VIDEO 2 OUT outputs for
recording.
3. Start recording at the recording component as desired.
To confirm the settings, press the Rec Out button. The current
settings will appear for 8 seconds in the front display.
Notes:
• Be aware that the remote (Zone 2) and recording (REC OUT)
outputs use the same circuit and therefore cannot be used at the
same time.
• You cannot record the surround effects.
• Digital signals input to the DIGITAL INPUT (COAX) and
DIGITAL INPUT (OPT) inputs will be output to the DIGITAL
OUTPUT (OPT) outputs.
• There are some restrictions on recording digital signals. When
making digital recordings, consult the instruction manual that
came with your digital recording equipment (e.g., MD recorder
or DAT deck) to know what restrictions are imposed.
• You cannot record the source connected to the MULTI CH
INPUT connector.
• You cannot listen to a broadcast from one station while
recording the broadcast from another.