Onkyo TX-NR900E - Manual (Page 30)

30
Turning on the power from the remote controller
Before you can use the remote controller, you must perform steps 1
and 2 above and place the TX-NR900/900E in the standby state.
1. Press the RCVR MODE button.
The RCVR MODE button lights.
2. Press the ON button to turn on the
TX-NR900/900E (take it out of the
standby state).
To return the TX-NR900/900E to the
standby state, press the STANDBY button.
Memory preservation (Other than USA and Canadian
models)
The TX-NR900/900E does not require memory preservation
batteries. A built-in memory backup system preserves the
contents of memory (e.g., speaker settings and surround settings)
during power failures and even when the power is turned off with
the POWER switch. The backup system is charged when the
POWER switch is turned on.
The length of time that the memory will be preserved will vary
depending on the ambient climate. On the average, memory
contents are protected over a period of a few weeks after the last
time the unit has been turned off. This period may be shorter
when the unit is exposed to a highly humid climate.
Memory preservation (USA and Canadian models)
The TX-NR900 does not require memory preservation batteries.
A built-in memory backup system preserves the contents of
memory (e.g., speaker settings and surround settings) during
power failures and even when the unit is unplugged. The unit
must be plugged in order to change the back-up system.
The length of time that the memory will be preserved will vary
depending on the ambient climate. On the average, memory
contents are protected over a period of a few weeks after the last
time the unit has been unplugged. This period may be shorter
when the unit is exposed to a highly humid climate.
• Before you plug in the TX-NR900/900E, confirm that all
connections have been made properly.
• Turning on the power may cause a momentary power surge,
which might interfere with other electrical equipment on the
same circuit, such as computers. If this happens, use a wall outlet
on a different circuit.
(All models other than USA and Canadian models)
• The TX-NR900/900E is shipped with the main power (POWER)
switch in the on position ( ON ). When the power cord is
plugged in for the first time, the TX-NR900/900E will
automatically enter the standby state and the STANDBY
indicator will light (same condition after step 2 below).
Turning on the power
1. Plug the power cord into an AC wall outlet.
(USA and Canadian models)
The STANDBY indicator will light up.
(All models other than USA and Canadian models)
Press the POWER switch to set the
TX-NR900/900E to standby state.
The STANDBY indicator will light up.
2. Press the STANDBY/ON button to turn on the TX-
NR900/900E.
The display will light up and the
STANDBY indicator will turn off.
If you press the STANDBY/ON button
again, the receiver returns to Standby
state.
Connecting the power
Turn off
PUSH TO OPEN
TX-NR900E
STANDBY/ON
STANDBY
DVD ZONE 2 ( ) GRN REC ( ) RED AUDIO SELECTOR PURE AUDIO UPSAMPLING
OFF ON
POWER
MASTER VOLUME
TUNER PHONO NET AUDIO C D TAPE VIDEO 3 VIDEO 5 VIDEO 4 VIDEO 2 VIDEO 1
VCR 2 VCR 1
DISPL AY
PUSH TO OPEN
TX-NR900
STANDBY/ON
STANDBY
MASTER VOLUME
TUNER PHONO NET AUDIO C D TAPE DVD VIDEO 3 VIDEO 5 VIDEO 4 VIDEO 2 VIDEO 1
VCR 2 VCR 1
ZONE 2 ( ) GRN REC ( ) RED AUDIO SELECTOR DISPL AY PURE AUDIO UPSAMPLING
POWER
STANDBY/ON STANDBY/ON ON
RCVR
STANDBY
OFF ON
POWER
STANDBY
STANDBY/ON
STANDBY
To wall outlet
STANDBY
To wall outlet
STANDBY indicator STANDBY indicator
(USA and Canadian models) (All models other than USA and Canadian models)