Radio Shack 900 MHz Digital Spread Spectrum Cordless Phone with Digital Answerer and Caller ID/Call Waiting Deluxe - Manual (Page 17)

17 Telephone Operation
1. Lift the handset.
2. Hold down MEM until
C[ceho C[ceho C[ceho C[ceho Ij Ij Ij Ijeh[ eh[ eh[ eh[
and a
list of memory location numbers appear.
3. Press the appropriate numbers to
choose the desired two-digit memory
location (01–20). Precede a single digit
location number with 0 (01, 02, 03, and
so on).
4. Press SELECT .
Ijeh[ý DWc[ Ijeh[ý DWc[ Ijeh[ý DWc[ Ijeh[ý DWc[
appears. If
you do not want to enter a name, skip to
Step 6.
5. To enter a name, use the number keys.
Refer to the letters on the number keys
to select the desired letter. Press the key
once for the first letter in upper case,
press twice for the second letter in upper
case, and so on. To enter a lower case
letter, press four times (or five times) to
display the first letter in lower case, five
or six times for the second letter, and so
on.
For example, to enter John: press 5
once; upper case
@@@@
appears. Then press
6 six times; lower case
eeee
appears. Press
4 five times; lower case
^^^^
appears.
Finally, press 6 five times; lower case
dddd
appears.
To enter two letters from the same key in
a row, press
FLASH/
7 7 7 7
to move the cur-
sor to the next position. For example, to
enter AB, press
2 ;
7777
appears. Then
press FLASH/
7 7 7 7
, the cursor moves to
the next position, then press 2 twice so
8888
appears.
To enter a space, press FLASH/
7 7 7 7
twice
without entering any character.
To enter a number, repeatedly press the
corresponding number key until the
number appears.
To enter a special character, use 0 . Each
time you press 0 , the following charac-
ters appear in this order:
∗
з зз з ¶э ¶э¶э ¶э
&
вэб вэбвэб вэб
(space)
&ý &ý &ý &ý
If you make a mistake, use REDIAL/
6 6 6 6
or FLASH/
7 7 7 7
to move the cursor over
the error, then enter the correct charac-
ter, or press
DELETE/CH to delete a
character. To delete all characters, hold
down
DELETE/CH for at least 1 second.
6. Press SELECT .
Ijeh[ýDkcX[h Ijeh[ýDkcX[h Ijeh[ýDkcX[h Ijeh[ýDkcX[h
appears.
7. Enter the phone number and any tone or
pause entries.
8. Press SELECT . The phone beeps and
C[cehoddýIjeh[Z C[cehoddýIjeh[Z C[cehoddýIjeh[Z C[cehoddýIjeh[Z
(
dd dd dd dd
is the memory loca-
tion number) appears.
After 2 seconds,
C[cehoýIjeh[ C[cehoýIjeh[ C[cehoýIjeh[ C[cehoýIjeh[
appears.
Repeat Steps 3–8 to store more num-
bers.
9. When you finish, press MEM .
Note: To replace a stored number, store a
new one in its place.
Editing or Deleting a Number in
Memory
1. Lift the handset.
2. Hold down MEM until
C[cehoýIjeh[ C[cehoýIjeh[ C[cehoýIjeh[ C[cehoýIjeh[
and a
list of memory location numbers appear.
3. Choose a memory location (01–20) by
pressing a number or by repeatedly
pressing
VOL/CID
8 8 8 8
or
9 9 9 9
.
4. Press SELECT . A menu appears with the
following three options.
;Z_jý C[cehodd ;Z_jý C[cehodd ;Z_jý C[cehodd ;Z_jý C[cehodd
— edit the record as
described in Steps 5 through 8 of “Stor-
ing a Name and Number in Memory” on
Page 16.