RCA RP5605R - Manual

Stop the wake function:
Press OFF. The wake function will
activate again on the following day
at the same time.
Cancel the wake function
completely:
Press WAKE MODE repeatedly until
no indicator lights against the wake
source icons. The set wake time will
not be erased and can be used the
next time when you switch on wake
function again.
Setting clock
1. Press CLOCK SET once. The
current clock time fl ashes on the
display.
2. Press or to set the clock
time. The time decrements or
increments will follow by a faster
rate when you press and hold
the buttons. AM or PM indicator
also lights beside the time on the
display.
user manual
guide de l’utilisateur
EN/F
It is important to read this user manual prior to using your new product for the fi rst time.
Nous vous recommandons de lire ce manuel d’instructions avant d’utiliser votre nouveau
produit pour la première fois.
RP5605
RP5605R
v6.0 (1.0.6.0) (EN/F) IMPORTANT SAFETY INSTRUCTIONS
Sleep function
Top view
If you set Sleep function
with low volume level
before going to bed, we
advise using Wake to Alarm mode.
Battery back-up operation
The power failure protection circuit
will not operate unless battery is
installed.
No worry battery backup
When the battery backup functions,
the digital display will not light,
however, the wake function still
occurs during the power interruption
if remaining battery power is
adequate.
Normal operation will resume after
AC power is restored so you will not
have to reset the time or wake.
Left view
Right view TUNING – selects radio frequency
BAND AM/FM – selects radio band
Switching on
Press RADIO ON to turn on the
radio.
Switching band
Slide the BAND/AM•FM switch on
the right of the unit to select AM or
FM band.
Tuning radio
Rotate the TUNING dial on the right
of the unit to select radio frequency.
Antennas
AM Antenna – A built-in ferrite
rod antenna eliminates the need
for an outside antenna for AM
reception. Rotating the unit slightly
may improve reception of distant
AM stations.
Setting wake time
1. Press WAKE TIME once. The
current wake time fl ashes on the
display.
2. Press or to set the wake
time. The time decrements or
increments will follow by a faster
rate when you press and hold
the buttons. AM or PM indicator
also lights beside the time on the
display.
3. When fi nished, wait for about 5
seconds or press WAKE TIME to
exit wake time setting mode.
• The Wake to Alarm mode (read
below) will be automatically
activated whenever the wake
time has been set.
Selecting wake source
1. If your desired wake source is
radio or CD:
• Wake to Radio – select an AM or
FM station (refer to “Radio”).
• Wake to CD – insert a CD in the
CD compartment.
2. Set a wake time (refer to
“Setting wake time”).
3. Press WAKE MODE repeatedly
to select a wake source. The
indicator lights against the wake
source icons on the right of the
display to indicate the currently
selected wake source:
• Once the wake source is selected,
the wake function will be
activated at the set wake time.
Checking wake time
Press WAKE TIME to show the
current wake time which fl ashes
briefl y on the display.
You can set the duration (up to 90
min) before the radio or CD player
turns off automatically.
1. Press SLEEP repeatedly to select
a duration (90, 80, 70, 60, 50,
40, 30, 20, 10min or OFF) before
the radio or CD player turns off
automatically.
• The default sleep time is 60
minutes.
• By default, the radio will be
switched on once SLEEP is
pressed. You may change to
listen to the CD player by
pressing
if a disc is loaded.
2. To check the remaining duration
before the unit turns off, press
SLEEP once.
3. To cancel the sleep function,
press SNOOZE or OFF.
Alkaline (NEDA 1604A/
IEC 6LR61) battery is
recommended. Carbon-
zinc battery may be used but
memory holding time will be
substantially reduced. Memory
holding time for a fresh alkaline
battery is approximately 8
hours (if radio or alarm are not
operated) which should take
care of short, nuisance-type
AC power failures. To preserve
battery life, the unit should
remain plugged into an AC
outlet. As the battery gets older,
its voltage drops and memory
may be lost. Be sure to replace
the battery periodically. Battery
should be removed if the unit
will be stored for more than one
month. Leaky battery can badly
damage the clock radio.
For your records
In the event that service should be
required, you may need the model
number and the serial number. In
the space below, record the date
and place of purchase and the serial
number:
Model No.:
Date of Purchase:
Place of Purchase:
Serial No.:
Service information
This product should be serviced
only by those specially trained in
appropriate servicing techniques.
For instructions on how to obtain
service, refer to the warranty
included in this user manual.
Technical information
Product: CD/Clock Radio
Brand: RCA
Model: RP5605, RP5605R
Power Supply: 120V ~ 60Hz
Power Consumption: 13 Watts
RADIO ON – turns on the radio;
selects the radio from other modes
OFF – turns off the unit; turns off the
wake function and sleep mode
/ – sets clock or wake time;
skips to previous or next CD track
during CD playback
+ VOLUME – – adjusts volume
Listening to CD
1. Lift open the CD compartment
door.
2. Insert a disc and close the door.
3. Press to select CD mode and
start CD playback.
• Press to pause playback and
press again to resume.
4. Adjust volume to your desired
level.
5. Press or to skip backward
or forward a track. Press and
hold to search through a track.
6. Press to stop playback.
7. Press RADIO ON to listen to the
radio or OFF to turn off the unit.
wake by alarm
wake by radio
wake by CD
Turning off the wake
function
Silence the wake function
momentarily:
• With SmartSnooze™, press
SNOOZE, , , or to
turn off the wake function
temporarily for extra sleep time.
• The wake function will activate
again when the snooze period (9
minutes) is over.
• The snooze period is fi xed and
cannot be changed.
• If disc is paused for
more than 5 minutes,
the CD player will
resume to stop mode
automatically.
• If disc is stopped in the CD
mode for more than 30
minutes without further
operations, the unit will turn
off automatically.
PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE
Before you begin
Power failure indicator
When AC power is interrupted
(disconnected) for a short period of
time, both time and alarm settings
will change (unless battery is
installed). After AC power is restored
(reconnected), the Digital Display
will blink to indicate that power was
interrupted and you should readjust
the time and alarm settings.
– stops CD playback
– turns on the unit from CD mode;
pauses or resumes CD playback
SLEEP – activates the Sleep function
CLOCK SET – activates clock time
setting mode
WAKE TIME – activates wake time
setting mode; checks current wake
time
WAKE MODE – activates wake
function and changes wake mode
SNOOZE – turns off the wake
function temporarily; cancels the
sleep function
Clock Radio
FM Antenna – The power cord acts
as your FM antenna. The power
cord picks up moderate to strong
stations and eliminates the need for
an external antenna in most strong
signal areas. Be sure the power cord
is stretched out to its full length. Do
not coil or bunch the cord together.
Changing position of the power cord
may improve reception.
Built-In AFC – The Built In
Automatic Frequency Control (AFC)
works only on FM. It helps reducing
drift on FM reception and keeping
the radio locked in on the FM station
to which it is tuned.
When tuning in FM stations, you
may notice that the station you are
tuning can be well-tuned on two
or three nearby points on the dial.
Always tune carefully at the loudest
and clearest point.
CD player Wake function
General controls
Warranty information
Warranty information
12 Month Limited Warranty
Applies to RCA Audio/Video
Products
• AUDIOVOX ELECTRONICS CORP.
(the Company) warrants to the
original retail purchaser of this
product that should this product
or any part thereof, under
normal use and conditions, be
proven defective in material or
workmanship within 12 months
from the date of original
purchase, such defect(s) will
be repaired or replaced with
reconditioned product (at the
Company’s option) without
charge for parts and repair labor.
• To obtain repair or replacement
within the terms of this
Warranty, the product is to be
delivered with proof of warranty
coverage (e.g. dated bill of
sale), specifi cation of defect(s),
transportation prepaid, to the
Company at the address shown
below.
• This Warranty does not extend
to the elimination of externally
generated static or noise, to
correction of antenna problems,
loss/interruptions of broadcast
or internet service, to costs
incurred for installation, removal
or reinstallation of product, to
corruptions caused by computer
viruses, spyware or other
malware, to loss of media, fi les,
data or content, or to damage to
tapes, discs, removable memory
devices or cards, speakers,
accessories, computers, computer
peripherals, other media players,
home networks or vehicle
electrical systems.
• This Warranty does not
apply to any product or
part thereof which, in the
opinion of the Company, has
suffered or been damaged
through alteration, improper
installation, mishandling,
misuse, neglect, accident, or by
removal or defacement of the
factory serial number/bar code
label(s). THE EXTENT OF THE
COMPANY’S LIABILITY UNDER
THIS WARRANTY IS LIMITED TO
THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO
EVENT, SHALL THE COMPANY’S
LIABILITY EXCEED THE PURCHASE
PRICE PAID BY PURCHASER FOR
THE PRODUCT.
• This Warranty is in lieu of
all other express warranties
or liabilities. ANY IMPLIED
WARRANTIES, INCLUDING
ANY IMPLIED WARRANTY
OF MERCHANTABILITY,
SHALL BE LIMITED TO THE
DURATION OF THIS WRITTEN
WARRANTY. ANY ACTION FOR
BREACH OF ANY WARRANTY
HEREUNDER INCLUDING ANY
IMPLIED WARRANTY OF
MERCHANTABILITY MUST BE
BROUGHT WITHIN A PERIOD
OF 24 MONTHS FROM DATE
OF ORIGINAL PURCHASE.
IN NO CASE SHALL THE
COMPANY BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS
OR ANY OTHER WARRANTY.
No person or representative is
authorized to assume for the
Company any liability other than
expressed herein in connection
with the sale of this product.
• Some states do not allow
limitations on how long an
implied warranty lasts or the
exclusion or limitation of
incidental or consequential
damage so the above limitations
or exclusions may not apply to
you. This Warranty gives you
specifi c legal rights and you may
also have other rights which vary
from state to state.
How to make a warranty claim:
• If your product is capable of
storing content (such as an mp3
player, digital voice recorder,
etc), it is recommended to
make periodic backup copies of
content stored on the product.
If applicable, before shipping a
product, make a back up copy
of content or data stored on
the device. Also, it is advisable
to remove any personal
content which you would not
want exposed to others. IT IS
LIKELY THAT CONTENTS AND
DATA ON THE DEVICE WILL BE
LOST DURING SERVICE AND
REFORMATTING. AUDIOVOX
ACCEPTS NO LIABILITY FOR LOST
CONTENT OR DATA, OR FOR THE
SECURITY OF ANY PERSONAL
CONTENT OR DATA ON THE
RETURNED DEVICE. Product will
be returned with factory default
settings, and without any pre-
loaded content which may have
been installed in the originally
purchased products. Consumer
will be responsible for reloading
data and content. Consumer will
be responsible to restore any
personal preference settings.
• Properly pack your unit. Include
any remotes, memory cards,
cables, etc. which were originally
provided with the product.
However DO NOT return any
removable batteries, even if
batteries were included with
the original purchase. We
recommend using the original
carton and packing materials.
• Include evidence of purchase
date such as the bill of sale. Also
print your name and address and
a description of the defect. Send
via standard UPS or its equivalent
to:
Audiovox Electronics Corp.
Attn: Service Department.
150 Marcus Blvd.
Hauppauge N.Y. 11788
1-877-833-3491
• Insure your shipment for loss or
damage. Audiovox accepts no
liability in case of damage or loss
en route to Audiovox.
• Pay any charges billed to you by
the Exchange Center for service
not covered by the warranty.
• A new or refurbished unit will be
shipped to you freight prepaid.
What we will do:
Provide you with a new, or at our
option, a refurbished unit. The
exchange unit is under warranty
for the remainder of the original
product’s warranty period.
For Canada Customers, please
ship to:
Audiovox Return Centre
c/o Genco
6685 Kennedy Road,
Unit#3, Door 16,
Mississuaga, Ontario
L5T 3A5
© 2010 Audiovox Accessories Corporation
111 Congressional Blvd., Suite 350
Carmel, IN 46032
Trademark(s) ® Registered
Printed in China
Visit http://store.audiovox.com to find the best
accessories for your products.
Some of the following information
may not apply to your particular
product; however, as with any
electronic product, precautions
should be observed during handling
and use.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near
water.
• Clean only with dry cloth.
• Do not block any ventilation
openings. Install in accordance
with the manufacturer’s
instructions.
• Do not install near any heat
sources such as radiators, heat
registers, stoves, or other
apparatus (including amplifi ers)
that produce heat.
• Do not defeat the safety purpose
of the polarized or grounding-
type plug. A polarized plug
has two blades with one wider
than the other. A grounding
type plug has two blades and
a third grounding prong. The
wide blade or the third prong is
provided for your safety. If the
provided plug does not fi t into
your outlet, consult an electrician
for replacement of the obsolete
outlet.
• Protect the power cord from
being walked on or pinched
particularly at plugs, convenience
receptacles, and the point where
they exit from the apparatus.
• Only use attachments/accessories
specifi ed by the manufacturer.
• Use only
with the
cart, stand,
tripod,
bracket,
or table
specifi ed by
the manufacturer, or sold with
the apparatus. When a cart is
used, use caution when moving
the cart/apparatus combination
to avoid injury from tip-over.
• Unplug this apparatus during
lightning storms or when unused
for long periods of time.
• Refer all servicing to qualifi ed
service personnel. Servicing is
required when the apparatus
has been damaged in any way,
such as power-supply cord or
plug is damaged, liquid has been
spilled or objects have fallen into
the apparatus, the apparatus
has been exposed to rain or
moisture, does not operate
normally, or has been dropped.
ADDITIONAL SAFETY
INFORMATION
• Apparatus shall not be exposed
to dripping or splashing and no
objects fi lled with liquids, such
as vases, shall be placed on the
apparatus.
• Always leave suffi cient space
around the product for
ventilation. Do not place
product in or on a bed, rug, in
a bookcase or cabinet that may
prevent air fl ow through vent
openings.
• Do not place lighted candles,
cigarettes, cigars, etc. on the
product.
• Connect power cord only to AC
power source as marked on the
product.
• Care should be taken so that
objects do not fall into the
product.
• Do not attempt to disassemble
the cabinet. This product does
not contain customer serviceable
components.
• The marking information
is located at the bottom of
apparatus.
• To be completely disconnect the
power input, the main plug of
apparatus shall be disconnected
from the mains.
• Main plug is a disconnect device.
The main plug should not be
obstructed OR should be easily
accessed during intended use.
• The ventilation should not
be impeded by covering the
ventilation openings with items
such as newspaper, table-cloths,
curtains etc.
• No naked fl ame sources such as
lighted candled should be placed
on the apparatus.
• Attention should be drawn to
the environmental aspects of
battery disposal.
• The use of apparatus in
moderate climates.
This equipment is a Class
II or double insulated
electrical appliance. It
has been designed in
such a way that it does
not require a safety
connection to electrical
earth.
Plugging in for power
AC OUTLET POWER SUPPLY:
120 V~60 Hz
The AC power plug
is polarized (one
blade is wider than
the other) and only
fi ts into AC power
outlets one way.
If the plug will
not go into the outlet completely,
turn the plug over and try to insert
it the other way. If it still does not
fi t, contact a qualifi ed electrician to
change the outlet, or use a different
one. Do not attempt to bypass this
safety feature.
Important battery
precautions
• Any battery may present a risk of
fi re, explosion, or chemical burn
if abused. Do not try to charge
a battery that is not intended to
be recharged, do not incinerate,
and do not puncture.
• Non-rechargeable batteries,
such as alkaline batteries, may
leak if left in your product for
a long period of time. Remove
the batteries from the product if
you are not going to use it for a
month or more.
• If your product uses more than
one battery, do not mix types
and make sure they are inserted
correctly. Mixing types or
inserting incorrectly may cause
them to leak.
• Discard any leaky or deformed
battery immediately. They
may cause skin burns or other
personal injury.
• Please help to protect the
environment by recycling or
disposing of batteries according
to federal, state, and local
regulations.
]
Portable Cart Warning
Note: This equipment has been
tested and found to comply with
the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules.
These limits are designed to provide
reasonable protection against
harmful interference in a residential
installation. This equipment
generates, uses, and can radiate
radio frequency energy and, if not
installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications.
However, there is no guarantee
that interference will not occur
in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and
on, the user is encouraged to try to
correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between
the equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from
that to which the receiver is
connected.
• Consult the dealer or an
experienced radio/TV technician
for help.
Changes or modifi cations not
expressly approved by Audiovox
could void the user’s authority to
operate the equipment.
FCC Information
WARNING: The battery (battery or
batteries or battery pack) shall not
be exposed to excessive heat such as
sunshine, fi re or the like.
Ecology
Help protect the environment - we
recommend that you dispose of
used batteries by putting them into
specially designed receptacles.
Illustrations contained within this
publication are for representation
only and subject to change.
The descriptions and characteristics
given in this document are given as
a general indication and not as a
guarantee. In order to provide the
highest quality product possible,
we reserve the right to make any
improvement or modifi cation
without prior notice.
Install battery as follow:
1. Remove battery compartment
door (located at the bottom of
the radio) by applying thumb
pressure to the tab on battery
door and then lift the door out
and off the cabinet.
2. Connect a 9-volt battery (not
supplied) to the connector plug.
3. Replace the compartment door.
3. When fi nished, wait for about 5
seconds or press CLOCK SET to
exit clock setting mode.