RCA RC10 - Manual

SET
AM
PM
user manual
guide de l’utilisateur
RC10
v3.0 (EN/F)
The descriptions and characteristics in
this owner’s manual are for the purpose
of general reference only and not as a
guarantee. In order to provide you with
the highest quality product, we may
make changes or modifi cations without
prior notice.
Before you begin
Clock
WARNING:
TO PREVENT FIRE
OR ELECTRICAL
SHOCK HAZARD,
DO NOT EXPOSE
THIS PRODUCT
TO RAIN OR
MOISTURE.
SEE MARKING ON BOTTOM OF PRODUCT
EN/F
It is important to read this user manual prior to using your new product for the fi rst time.
Nous vous recommandons de lire ce manuel d’instructions avant d’utiliser votre
nouveau produit pour la première fois.
FCC information
This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined
by turning the equipment off and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet
on a circuit different from that to
For your records
In the event that service should be
required, you may need the model
number and the serial number. In the
space below, record the date and place
of purchase and the serial number:
Model No.:
Date of Purchase:
Place of Purchase:
Serial No.:
which the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
Modifications not expressly approved
by the party responsible for compliance
could void the user’s authority to operate
the equipment.
This Class B digital apparatus complies
with Canadian ICES-003.
Cet appareil numérique de la classe B
est conforme à la norme NMB-003 du
Canada.
Maufacturer/Responsible Party
Audiovox Electronics Corp.
150 Marcus Blvd., Hauppauge, NY 11788
PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE
IMPORTANT SAFETY INSTRUCTIONS
Some of the following information may
not apply to your particular product;
however, as with any electronic product,
precautions should be observed during
handling and use.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near
water.
• Clean only with dry cloth.
• Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
• Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifi ers) that produce heat.
• Do not defeat the safety purpose
of the polarized or grounding-type
plug. A polarized plug has two
blades with one wider than the
other. A grounding type plug has
two blades and a third grounding
prong. The wide blade or the third
prong is provided for your safety. If
the provided plug does not fi t into
your outlet, consult an electrician
for replacement of the obsolete
outlet.
• Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
• Only use attachments/accessories
specifi ed by the manufacturer.
• Use only with the cart,
stand, tripod, bracket,
or table specifi ed by
the manufacturer, or
sold with the apparatus.
When a cart is used, use caution
when moving the cart/apparatus
combination to avoid injury from
tip-over.
• Unplug this apparatus during
lightning storms or when unused
for long periods of time.
• Refer all servicing to qualifi ed
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as power-supply cord or plug is
damaged, liquid has been spilled
or objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does
not operate normally, or has been
dropped.
ADDITIONAL SAFETY INFORMATION
• Main plug is used as disconnect
device and it should remain readily
operable during intended use. In
order to disconnect the apparatus
from the mains completely, the
mains plug should be disconnected
form the mains socket outlet
completely.
• Apparatus shall not be exposed to
dripping or splashing and no objects
fi lled with liquids, such as vases,
shall be placed on the apparatus.
• Always leave suffi cient space around
the product for ventilation. Do
not place product in or on a bed,
rug, in a bookcase or cabinet that
may prevent air fl ow through vent
openings.
• Do not place lighted candles,
cigarettes, cigars, etc. on the
product.
• Connect power cord only to AC
power source as marked on the
product.
• Care should be taken so that objects
do not fall into the product.
• Do not attempt to disassemble
the cabinet. This product does
not contain customer serviceable
components.
• The marking information is located
at the bottom of apparatus.
• Caution marking is located at
bottom of apparatus.
]
Technical information
Product: Clock Radio
Brand: RCA
Model: RC10
Electrical consumption
Power Supply: 120V ~ 60Hz
Power Consumption: 5 Watts
SNOOZE (on top of unit) – enter
snooze mode where the alarm will quiet
but sound again once the snooze period
is over.
OFF – turn off the unit.
ON (RADIO) – turn on the radio.
REV – set clock or wake time
(decrease value).
FWD – set clock or wake time
(increase value).
SLEEP – activate sleep function.
WAKE MODE – select wake mode.
SET / / – slide switch to set
wake or clock time.
General controls
–VOLUME+ – adjust volume.
BAND – select between AM and FM
bands.
TUNING – select radio frequencies.
Radio
Selecting radio mode
Press ON (RADIO) to switch on radio.
Switching band
Slide the BAND switch on the right of
the unit to select FM or AM band.
Tuning the radio
Rotate the TUNING knob on the right of
the unit to adjust the radio frequency.
Built-in AFC
The Built In Automatic Frequency
Control (AFC) works only on FM. It helps
reducing drift on FM reception and
keeping the radio locked in on the FM
station to which it is tuned.
When tuning in FM stations, you may
notice that the station you are tuning
can be well-tuned on two or three
nearby points on the dial. Always tune
carefully at the loudest and clearest
point.
AM antenna
A built-in ferrite rod antenna eliminates
the need for an outside antenna for
AM reception. Rotating the unit slightly
may improve reception of distant AM
stations.
Setting wake time
1. Slide the switch SET / / to
position.
2. Press REV or FWD to set the
wake time on the small display.
• The time decrements or increments
will follow by a faster rate when
you press and hold the buttons.
3. Slide the switch SET / / to
position.
Selecting wake source
You may be woken up by radio or
alarm.
1. Set a wake time (see above
instructions).
2. Press WAKE MODE repeatedly to
select a waking mode.
• Corresponding indicator lights
against the wake icon on the small
display.
– Wake by alarm
– Wake by radio
• The unit equips with GRAD-U-
WAKE feature, the alarm tone
volume will increase gradually to
its maximum in about 30 to 45
seconds.
• Your last tuned radio station will be
the wake source if wake by radio is
selected.
Turning off the wake
alarm or radio
• To silence the wake function
momentarily:
To turn off the wake function, press
SNOOZE on the top of the unit.
The wake alarm or radio will be
switched off temporarily. The alarm
or radio will be on again when the
snooze period (default: 9 minutes) is
over. (read “SmartSnooze
TM ”)
• To turn off the wake alarm or
radio:
Press OFF. The wake alarm or radio
will activate again the next day
unless you switch off the Wake
function.
• To disable the wake function
completely:
Press WAKE MODE repeatedly until
OFF shows on the small display.
Checking wake time
• The set wake time always shows on
the small display with a wake mode
selected.
• If wake function is not activated,
OFF shows on the small display.
Wake function
SmartSnooze TM
This operation allows extra sleep time
after the wake function is on. The alarm
will be off by pressing SNOOZE, ON,
REV, FWD or SLEEP until the snooze
period is over. Snooze function can be
used repeatedly up to 60 minutes. After
this, the wake function will turn off
until the next day.
To set the “quiet” period:
1. Press and hold SNOOZE.
2. Press REV or FWD to set the
quiet period that shows on the
large display.
• The time decrements or increments
will follow by a faster rate when
you press and hold the buttons.
• Snooze period can be set from 1 to
30 minutes (default: 9 minutes).
3. Release SNOOZE.
SmartSnooze TM is only
available when the switch
SET
/ / is at the
position.
In sleep mode, you can set the duration
(up to 90 minutes) before the radio turn
off automatically.
To set the sleep mode:
• Press SLEEP repeatedly to cycle
among the sleep times available
(90min, 60min, 30min, 15min and
OFF. 90min is the default setting) on
the large display.
• The radio will be switched on.
• The indicator lights against the
sleep icon on the large display
when sleep mode is activated.
To check the remaining time in
sleep mode:
• Press and hold SLEEP to check the
remaining sleep time on the large
display.
To cancel the sleep mode:
• If you decide to turn off the unit
sooner, press SNOOZE or OFF.
Sleep function
Audiovox Electronics Corp.,
150 Marcus Blvd., Hauppauge, NY 11788
©2009 Audiovox Electronics Corp.
Trademark(s) ® Registered
Marque(s) ® Deposée(s)
Marca(s) ® Registrada(s)
www.rcaaudiovideo.com
Printed in China
Warranty information
12 Month Limited Warranty
Applies to RCA Audio/Video
Products
AUDIOVOX ELECTRONICS CORP. (the
Company) warrants to the original retail
purchaser of this product that should
this product or any part thereof, under
normal use and conditions, be proven
defective in material or workmanship
within 12 months from the date of
original purchase, such defect(s) will be
repaired or replaced with reconditioned
product (at the Company’s option)
without charge for parts and repair
labor.
To obtain repair or replacement
within the terms of this Warranty, the
product is to be delivered with proof
of warranty coverage (e.g. dated bill
of sale), specifi cation of defect(s),
transportation prepaid, to the Company
at the address shown below.
This Warranty does not extend to the
elimination of externally generated
static or noise, to correction of
antenna problems, loss/interruptions of
broadcast or internet service, to costs
incurred for installation, removal or
reinstallation of product, to corruptions
caused by computer viruses, spyware or
other malware, to loss of media, fi les,
data or content, or to damage to tapes,
discs, removable memory devices or
cards, speakers, accessories, computers,
computer peripherals, other media
players, home networks or vehicle
electrical systems.
This Warranty does not apply to any
product or part thereof which, in the
opinion of the Company, has suffered
or been damaged through alteration,
improper installation, mishandling,
misuse, neglect, accident, or by removal
or defacement of the factory serial
number/bar code label(s). THE EXTENT
OF THE COMPANY’S LIABILITY UNDER
THIS WARRANTY IS LIMITED TO THE
REPAIR OR REPLACEMENT PROVIDED
ABOVE AND, IN NO EVENT, SHALL THE
COMPANY’S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT.
This Warranty is in lieu of all other
express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING
ANY IMPLIED WARRANTY OF
MERCHANTABILITY, SHALL BE LIMITED
TO THE DURATION OF THIS WRITTEN
WARRANTY. ANY ACTION FOR BREACH
OF ANY WARRANTY HEREUNDER
INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY MUST BE
BROUGHT WITHIN A PERIOD OF 24
MONTHS FROM DATE OF ORIGINAL
PURCHASE. IN NO CASE SHALL THE
COMPANY BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR
ANY OTHER WARRANTY. No person or
representative is authorized to assume
for the Company any liability other than
expressed herein in connection with the
sale of this product.
Some states do not allow limitations on
how long an implied warranty lasts or
the exclusion or limitation of incidental
or consequential damage so the above
limitations or exclusions may not apply
to you. This Warranty gives you specifi c
legal rights and you may also have
other rights which vary from state to
state.
How to make a warranty claim:
• If your product is capable of storing
content (such as an mp3 player,
digital voice recorder, etc), it is
recommended to make periodic
backup copies of content stored
on the product. If applicable,
before shipping a product, make
a back up copy of content or data
stored on the device. Also, it is
advisable to remove any personal
content which you would not want
exposed to others. IT IS LIKELY
THAT CONTENTS AND DATA ON
THE DEVICE WILL BE LOST DURING
SERVICE AND REFORMATTING.
AUDIOVOX ACCEPTS NO LIABILITY
FOR LOST CONTENT OR DATA,
OR FOR THE SECURITY OF ANY
PERSONAL CONTENT OR DATA ON
THE RETURNED DEVICE. Product
will be returned with factory
default settings, and without any
pre-loaded content which may have
been installed in the originally
purchased products. Consumer will
be responsible for reloading data
and content. Consumer will be
responsible to restore any personal
preference settings.
• Properly pack your unit. Include
any remotes, memory cards, cables,
etc. which were originally provided
with the product. However DO NOT
return any removable batteries,
even if batteries were included
with the original purchase. We
recommend using the original
carton and packing materials.
• Include evidence of purchase date
such as the bill of sale. Also print
your name and address and a
description of the defect. Send via
standard UPS or its equivalent to:
Audiovox Electronics Corp.
Attn: Service Department.
150 Marcus Blvd., Hauppauge
N.Y. 11788
1-877-833-3491
• Insure your shipment for loss or
damage. Audiovox accepts no
liability in case of damage or loss en
route to Audiovox.
• Pay any charges billed to you by
the Exchange Center for service not
covered by the warranty.
• A new or refurbished unit will be
shipped to you freight prepaid.
What we will do:
Provide you with a new, or at our
option, a refurbished unit. The
exchange unit is under warranty for
the remainder of the original product’s
warranty period.
For Canada Customers, please ship
to:
Audiovox Return Centre
c/o Genco
6685 Kennedy Road,
Unit#3, Door 16,
Mississuaga, Ontario
L5T 3A5
Large display: Clock time
Small display:
Wake time and
wake mode
Plugging in for power
AC OUTLET POWER SUPPLY:
120V~60Hz
The AC power plug is polarized (one
blade is wider than the other) and only
fi ts into AC power outlets one way.
If the plug will not go into the outlet
completely, turn the plug over and try
to insert it the other way. If it still does
not fi t, contact a qualifi ed electrician
to change the outlet, or use a different
one. Do not attempt to bypass this
safety feature.
Battery back-up operation
• The power failure protection circuit
will not operate unless battery is
installed.
• When the battery backup functions,
the digital display will not light,
however, the wake function
still occurs during the power
interruption if remaining battery
power is adequate.
• Normal operation will resume after
AC power is restored so you will not
have to reset the time or wake.
Install battery as follow:
1. Remove battery compartment door
(located at the bottom of the radio)
by applying thumb pressure to the
tab on battery door and then lift
the door out and off the cabinet.
2. Connect a 9-volt battery (not
supplied) to the connector plug.
3. Replace the compartment door.
Power failure indicator
When AC power is interrupted
(disconnected) for a short period of
time, both time and alarm settings
will change (unless battery is
installed). After AC power is restored
(reconnected), the Digital Display
will blink to indicate that power was
interrupted and you should readjust the
time and alarm settings.
• Power is fed to the unit
even when it is not
functioning. To cut the
power supply off, the power
cable must be unplugged.
• Alkaline (NEDA 1604A/IEC
6LR61) battery is recommended.
Carbon-zinc battery may be
used but memory holding time
will be substantially reduced.
Memory holding time for a fresh
alkaline battery is approximately
8 hours (if radio or alarm are not
operated) which should take care
of short, nuisance-type AC power
failures. To preserve battery life,
the unit should remain plugged
into an AC outlet. As the battery
gets older, its voltage drops and
memory may be lost. Be sure to
replace the battery periodically.
Battery should be removed if the
unit will be stored for more than
one month. Leaky battery can
badly damage the clock radio.
Setting clock time
1. Slide the switch SET / / to
position.
2. Press REV or FWD to set the
clock time on the large display.
• The time decrements or increments
will follow by a faster rate when
you press and hold the buttons.
• The “:” between hour and minute
time fl ashes when you are setting
the time. AM or PM icon will also
show beside the time.
3. Slide the switch SET / / to
position.
Important Battery Precautions
• Any battery may present a risk of
fi re, explosion, or chemical burn
if abused. Do not try to charge a
battery that is not intended to be
recharged, do not incinerate, and
do not puncture.
• Non-rechargeable batteries, such as
alkaline batteries, may leak if left in
your product for a long period of
time. Remove the batteries from the
product if you are not going to use
it for a month or more.
• If your product uses more than one
battery, do not mix types and make
sure they are inserted correctly.
Mixing types or inserting incorrectly
may cause them to leak.
• Discard any leaky or deformed
battery immediately. They may
cause skin burns or other personal
injury.
• Please help to protect the
environment by recycling or
disposing of batteries according to
federal, state, and local regulations.
• Do not expose batteries to excessive
heat (for example, by leaving them
in sunlight or close to fi re).
SET
AM
PM
Front view
Right view
This is CLASS II apparatus with
double insulation, and no
protective earth provided.