Roland Bass Amplifier CB-60XL - Manual (Page 9)

7
Por
tuguês
Italiano
Deutsch
N
eder
lands
Español
Fr
anç
ais
English
To use the LOOPER function
17. [DELAY/LOOPER] Knob
Set the knob in the LOOPER range to turn on the LOOPER function. The
position of the knob within this range specifi es the LOOPER function’s
playback volume.
18. [REC/PLAY/DUB] Switch
Use this switch to record, play back, and overdub.
19. [TAP/STOP] Switch
This switch stops playback or erases the recording.
If the [DELAY/LOOPER] knob is in the LOOPER range, this switch stops
the LOOPER or erases the recording.
* For details on using the LOOPER function, refer to ”Using the
LOOPER” (p. 14).
* When the knob is positioned at LOOPER, no delay eff ect is applied.
To use the LOOPER and DELAY simultaneously, refer to ”Using the
LOOPER Function and DELAY at the Same Time” (p. 15).
REVERB
20. [REVERB] Knob
You can switch between use of two types of reverb by
changing the position of the knob. You can adjust the
intensity of the eff ect by varying the knob position.
The indicator lights up when REVERB is on and goes
out when the eff ect is off .
You can also switch REVERB on and off using an
optional footswitch pedal.
Knob Position Description
ROOM
This reverb simulates the short reverberant sound
heard within a room. Turning the knob clockwise
makes the eff ect progressively more intense.
PLATE
This is a plate reverb.
This reverb features high-end sustain. Turning the knob
clockwise makes the eff ect progressively more intense.
POWER SQUEEZER (CUBE-60XL BASS only)
21. [POWER SQUEEZER] Switch
The switch lights in red when the POWER SQUEEZER
function is on and goes out when the POWER SQUEEZER
is off .
Switching on the POWER SQUEEZER function allows you
to reduce the amp’s output to volume levels that are
suitable for the average home.
Switching this on allows you to produce a sound that preserves the
same tone and balance at volume levels that are suitable for the
average home.
* The POWER SQUEEZER function aff ects only sounds input through
the BASS INPUT jack. It has no eff ect on sounds input via the AUX IN
jack.
* The POWER SQUEEZER function will also aff ect the output from the
LINE OUT and RECORDING OUT/PHONES jacks; this is normal and
does not indicate a malfunction.
POWER
22. [POWER] Switch
This switches the power on and off .
Switching the Power On and Off
* Turn on power to your various devices in the order specifi ed. By
turning on devices in the wrong order, you risk causing malfunction
and/or damage to speakers and other devices.
1. Make sure that all [VOLUME] knobs on the CUBE-60XL BASS/
CUBE-120XL BASS and all the connected devices are set to 0.
2. Turn on all the devices connected to the CUBE-60XL BASS/
CUBE-120XL BASS’s input jacks (BASS INPUT jack and AUX IN
jack).
3. Turn on the CUBE-60XL BASS/CUBE-120XL BASS.
* Always make sure to have the volume level turned down before
switching on power. Even with the volume all the way down, you
may still hear some sound when the power is switched on, but this is
normal, and does not indicate a malfunction.
* This unit is equipped with a protection circuit. A brief interval (a
few seconds) after power up is required before the unit will operate
normally.
4. Adjust the volume levels for the devices.
5. Before switching off the power, lower the volume on all the
connected devices and then TURN OFF the devices in the
reverse order to which they were switched on.
* If you need to turn off the power completely, fi rst turn off the
POWER switch, then unplug the power cord from the power outlet.
Refer to Power Supply (p. 3).