Panasonic DMR-EH60 EN - Manual (Page 57)

57
RQT8307
Co
n
ven
ie
nt
fu
n
cti
o
n
s
Channel/Clock settings when TV Guide On Screen TM system is not used
Refer to the control reference on page 54.
Preparation:
If the television program list has already been downloaded, return the unit to the factory preset condition using the steps indicated below.
When the unit is on and stopped
1 Press and hold [
X CH] and [W CH] on the main unit for about five
seconds.
The unit turns off.
2 Press [ Í DVD POWER] to turn the unit on.
3 Complete the TV Guide On Screen TM system setup (until [ENTER]
is pressed after the “Watch TV” message screen is displayed).
[Note]
You can set scheduled recording only manually after you set the unit with “Set Channels Automatically”.
1
Press [SETUP].
2
Press [ 3, 4] to select “Channel” and
press [ 1].
3
Press [ 3, 4] to select “Set Channels
Automatically” and press [ENTER].
4
Press [ 2, 1] to select “Yes” and
press [ENTER].
5
Press [ENTER].
Auto Channel Setting starts. This takes a few minutes.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished.
≥DST, Daylight Saving Time, shows the summertime setting.
≥TIME ZONE shows the time difference from Greenwich
Mean Time (GMT).
EST (Eastern Standard Time) l GMT j5
CST (Central Standard Time) l GMT j6
MST (Mountain Standard Time) l GMT j7
PST (Pacific Standard Time) l GMT j8
AST (Alaska Standard Time) l GMT j9
HST (Hawaii Standard Time) l GMT j10
For other areas: xx hr
≥If the Auto Clock Setting does not start automatically, select
“Clock Settings” from the “Setup” tab and then select “Set
Clock Automatically”.
≥If the time was not set correctly, use manual clock setting
( ➡ 17) or adjust time zone.
6
Press [ENTER].
≥The unit configures channels according to the Signal Source
(RF IN) settings as follows.
Adjust the time zone ( j1 or i1) if it was not set correctly with auto
clock setting.
You cannot change this setting if you set the clock manually.
1
Press [SETUP].
2
Press [ 3, 4] to select “Setup” and
press [ 1].
3
Press [ 3, 4] to select “Clock
Settings” and press [ENTER].
4
Press [ 3, 4] to select “Adjust Time
Zone” and press [ENTER].
5
Press [ 3, 4] to select “s1” or “r1”
and press [ENTER].
To return to the previous screen
Press [RETURN].
To exit the screen
Press [SETUP].
To cancel partway while Auto Channel/Clock Setting is taking place
Press [RETURN].
To set so the television program list is not displayed automatically when you turn the unit on
➡ 29, “Review Options” menu–Selecting the TV Guide On Screen
TM system start up pattern
I N 2 I N 2
C H C H
HDD DVD SD
S VIDEO S VIDEO VIDEO VIDEO L/MONO L/MONO-AUDIO AUDIO-R
OPEN/CLOSE OPEN/CLOSE DRI DRIVE VE
SELECT SELECT REC REC
/x1.3
DV DV I N I N
X CH W
Auto channel/clock settings
Channel
SETUP
Setup
Disc
Video
Audio
Set Clock Automatically
Auto Clock Setting is complete.
4/4/2005 12:15 AM
DST.............. On
Time Zone..... CST
Signal Source
(RF IN)
Band Channel
Antenna
VHF 2–13
UHF 14–69
CableTV
VHF 2–13
CATV LOW BAND 95–99
CATV MID/SUPER BAND 14–36
CATV HYPER BAND 37–65
ULTRA BAND
66–94
100–125
SPECIAL CATV CHANNEL 1
Adjust Time Zone
SETUP
Setup
Disc
Video
Adjust Time Zone
j1
0
i1
Channel
EH60English.book Page 57 Monday, July 4, 2005 10:39 AM