Philips Network Adaper - Manual (Page 15)

29
T
RANSMITTER
C
ONTROL
O nce you have transmitted your message, you will
probably want to return control of the Receiver TVs
back to those TVs. If you selected “UNLOCKED” from
the ”RCVR LOCKOUT”sub-menu, then each TV has to
be reset at that TV. However, if you selected “LOCK,”
the locked TVs can be restored to their previous power,
channel, and cable settings from the Transmitter TV.
If not already in the “TRANSMITTER CON-
TROL” menu, press the D button on the remote control.
Then press the ▼ button until “RCVR LOCKOUT” is
highlighted.
Press the – ( ᮤ ) or + ( ᮣ ) button until “RESTORE”
is selected. (Note: you can also select “UNLOCK” from
this menu. Doing so, releases the Transmitter TV’s lock
on all Receiver TVs, but does not retore the Receiver
TVs to their previous settings.)
Press the ▼ button until “UPDATE RCVR TVS” is
highlighted. Then, press the – ( ᮤ ) or + ( ᮣ ) button.
“CURRENT” will appear beside “RCVR POWER” and
“RCVR CHANNEL.” The TV’s power, channel, and
cable are now restored to their previous settings.
Receiver Volume will have to be adjusted at each TV.
When finished, press the ▼ button to highlight
“EXIT.” Then press the “M” button. Or you can exit by
simply pressing the RECALL button when you’re done.
BEGIN
28
T
RANSMITTER
C
ONTROL
I f you select “LOCK” under “RCVR LOCKOUT,”
you have a couple of options in regards to “RCVR
POWER,” “RCVR VOLUME,” and “RCVR CHAN-
NEL.” Discussed below are the options.
O PTION 1: If you selected a setting (other than “CUR-
RENT”) for any of the three categories – Power,
Volume, Channel – the Receiver TVs will be locked
into those settings and can only be changed by the the
Transmitter TV. Also, “P,” “V,” or “C” will appear at the
top of the menu indicating that Power, Volume, or
Channel has been locked. You can lock one, two, or all
three. For example, if you set all TVs to “RCVR
POWER ON,” “RCVR VOLUME 35,” and “RCVR
CHANNEL 40,” then all TVs will power on, set their
volumes at 35, and tune to Channel 40. Also, none of the
Receiver TVs can be adjusted, except by you, and you
can even make changes without releasing the lock.
O PTION 2: If you selected “CURRENT” for any or all of
the settings, the Receiver TVs can make adjustments to
either Power, Volume, or Channel. For example, if you
left “RCVR VOLUME” at the default “CURRENT,”
then the Receiver TVs could be adjusted at the TV to the
best volume for the model of TV and the location.
TRANSMITTER CONTROL
*** (PVC) CTRL LOCK***
BROADCAST ALL SETS
RCVR POWER ON
RCVR VOLUME 35
RCVR CHANNEL 40
RCVR LOCKOUT LOCK
UPDATE RCVR TVS
EXIT MENU
PRESS +TO UPDATE RCVRS
TRANSMITTER CONTROL
*** (P–C) CTRL LOCK***
BROADCAST ALL SETS
RCVR POWER ON
RCVR VOLUME CURRENT
RCVR CHANNEL 40
RCVR LOCKOUT LOCK
UPDATE RCVR TVS
EXIT MENU
PRESS +TO UPDATE RCVRS
TRANSMITTER CONTROL
*** (P–C) CTRL LOCK***
BROADCAST ALL SETS
RCVR POWER ON
RCVR VOLUME CURRENT
RCVR CHANNEL 40
RCVR LOCKOUT RESTORE
UPDATE RCVR TVS
EXIT MENU
PRESS +TO UPDATE RCVRS
TRANSMITTER CONTROL
ADDRESS TYPE BROADCAST
BROADCAST ALL SETS
RCVR POWER CURRENT
RCVR VOLUME CURRENT
RCVR CHANNEL CURRENT
RCVR LOCKOUT UNLOCKED
UPDATE RCVR TVS
EXIT MENU
PRESS + TO UPDATE RCVRS
Net 1Card IB 2/15/00 12:18 PM Page 28