Panasonic DMR-ES40V - Manual (Page 15)

Getting started
15
VQT0R73
After plugging the unit into your household AC outlet and pressing
[
Í, DVD/VHS POWER] to turn the unit on for the first time, the unit
assists you in setting the on-screen language, and automatically
tunes in all the channels it can receive and sets the clock.
The unit automatically determines the type of transmission (airwaves
or cable) and puts them into channels as follows.
Preparation
≥Press [DVD].
≥Turn on the TV and select the appropriate video input to suit the
connections to the unit. (Example: AV input, CH3 or CH4)
≥If you connect the unit through a cable TV box or satellite receiver
( l 13), tune to your local PBS for Auto Clock Setting to work.
If there is no local PBS, set the clock manually ( l 44, “Set Clock
Manually”).
[1] Press [ Í, DVD/VHS POWER].
[2] Press [CH, W, X] to select an RF output channel
number.
The unit’s display
Each time you press the button:
CH3 (Default setting)
(# CH4 (# OFF
^-----------------------------------------------J
[3] Use [ 3, 4] to select the language and press
[ENTER].
[4] Press [ENTER] to start Plug-in Auto Tuning.
≥The unit then proceeds with Auto Clock Setting. The time is
displayed when Auto Clock Setting is finished.
≥DST, Daylight Saving Time, shows the summertime setting.
≥Time Zone shows the time difference from Greenwich Mean
Time (GMT).
EST (Eastern Standard Time) l GMT j5
CST (Central Standard Time) l GMT j6
MST (Mountain Standard Time) l GMT j7
PST (Pacific Standard Time) l GMT j8
AST (Alaska Standard Time) l GMT j9
HST (Hawaii Standard Time) l GMT j10
For other areas: xx hr
[5] Press [ENTER].
∫If the clock is an hour slower or faster than the actual
time
Select “ j1” or “i1” in “Adjust Time Zone” in the SETUP menu
( l 44).
∫If the unit couldn’t set the clock automatically
Set the time manually ( l 44, “Set Clock Manually”).
∫To start Plug-in Auto Tuning again
When the unit is on and stopped
[1] Press and hold [CH, W] and [CH, X] on the main unit for about 5
seconds.
The unit turns off.
[2] Press [ Í, DVD/VHS POWER] to turn the unit on.
Plug-in Auto Tuning starts.
STEP 2 Plug-in Auto Tuning
Band Channel
Antenna Mode
(Airwaves) VHF 2 to 13
UHF 14 to 69
CableTV Mode
(Cable)
VHF 2 to 13
CATV LOW BAND 95 to 99
CATV MID/SUPER BAND 14 to 36
CATV HYPER BAND 37 to 65
ULTRA BAND
66 to 94
100 to 125
SPECIAL CATV CHANNEL 1
PLAY
S
SCHEDULE
TIME SLIP
FUNCTIONS DIRECT NAVIGATOR
TOP MENU
RETURN
STATUS DISPLAY
SUB MENU
JET REW
OPERATION
SELECT
POWER
C S CANCEL/RESET
VOLUME CH INPUT SELECT
AUDIO
TV
TV/VIDEO
VHS DVD
TRACKING/V-LOCK
DVD/VHS POWER
VCR Plus+
DVD/VHS POWER
3, 4
ENTER
CH, W, X
Í
DVD DVD
English
Español
Français
Press ENTER
Pulse ENTER
Appuyer sur ENTER
Select Language
Seleccione el idioma
Sélection de Langue
Connection (without Audio/Video
cable):
Select “CH3” or “CH4” which displays
the screen on the right.
Connection (with Audio/Video
cable):
Select “OFF”
Signal source, RF output channel, channel caption, and
guide channel settings for VCR Plus
i system all revert to
the default values when you perform the procedure below.
Scheduled recording settings are also cleared.
The unit’s display
Set Channels Automatically
Ch.
Set Channels Automatically
Proceeding . . .
1 1 1
1
Set Clock Automatically
Auto Clock Setting is complete.
11/1/2005 12:15 AM
DST............. On
Time Zone.... CST
Ge
ttin
g
s
tart
e
d
ES40VP&PC.book 15 ページ ２００５年９月６日 火曜日 午前１０時２３分