Panasonic SC BTT268 - Manual (Page 36)

36
VQT3M40
Optional speaker settings Speaker installation
option
You can attach all of the speakers (except subwoofer) to a wall.
≥ The wall or pillar on which the speakers are to be attached
should be capable of supporting 10 kg (22 lbs) per screw.
Consult a qualified building contractor when attaching the
speakers to a wall. Improper attachment may result in
damage to the wall and speakers.
≥ Do not attempt to attach these speakers to walls using
methods other than those described in this manual.
1
Drive a screw (not supplied) into the wall.
2
Fit the speaker securely onto the screw(s)
with the hole(s).
Use the measurements indicated below to identify the
screwing positions on the wall.
≥ Leave at least 20 mm (
25 /
32
q) of space above the speaker and
10 mm ( 13 /
32
q) on each side to allow enough space for fitting
the speaker.
Front speaker,
Surround speaker
F 40 mm (1
9 /
16
q)
G 17.6 mm ( 11 /
16
q)
H 98.7 mm (3 7 /
8
q)
Center speaker
I 23 mm (
29 /
32
q)
J 95 mm to 97 mm
(3 3 /
4
q to 3 13 /
16
q)
K 26 mm (1 1 /
32
q)
L 16.7 mm ( 21 /
32
q)
M 63.7 mm (2 1 /
2
q)
Reference Troubleshooting guide
Before requesting service, please perform the
following steps.
The following do not indicate a problem with this unit:
jRegular disc rotating sounds.
jImage disturbance during search.
jImage disturbance when replacing 3D discs.
∫ Unit does not respond to the remote
control or front panel buttons.
Press and hold [POWER Í/I] on the main unit for 5 seconds.
jIf still unable to power the unit off, disconnect the power cord,
wait 1 minute, then reconnect the power cord.
∫ Cannot eject disc.
The unit may have a problem.
While the unit is off, press and hold [9] on the remote
control and [< OPEN/CLOSE] on the unit at the same time for
more than 5 seconds.
To return to the factory preset
≥ Select “Yes” in “Restore Default Settings” in the Setup menu.
( 34)
To return all settings to the factory preset
≥ Reset the unit as follows:
While the unit is off, press and hold [+ VOLUME], [< OPEN/
CLOSE] and [POWER Í/I] on the main unit at the same
time for more than 5 seconds.
The remote control doesn’t work properly.
≥ Change the batteries in the remote control. (
9)
≥ The remote control and main unit are using different codes. If
“SET ” is displayed on the unit’s display when a button is
pressed on the remote control, change the code on the
remote control. (
34)
Disc cannot be played.
≥ The disc is dirty. (
9)
≥ Check the region code.
Attaching to a wall
A At least 30 mm (1 3 /
16
q)
B ‰ 4.0 mm ( 5 /
32 q)
C ‰ 7.0 mm to ‰ 9.4 mm
(
9 /
32
q to 3 /
8
q)
D Wall or pillar
E 5.5 mm to 7.5 mm
( 7 /
32 q to 5 /
16 q)
e.g., Front speaker
DO NOT DO
≥ In this position, the
speaker will likely fall if
moved to the left or right.
≥ Move the speaker so that
the screw is in this
position.







 



  
Do you have the latest firmware installed?
Firmware updates may be released to correct operating
irregularities that are discovered with certain movies. (
17)
4
Make the following checks and visit our
website for more information.
http://www.panasonic.com/help
Enter the model number.
4
Or visit our website to find a service
center.
You can find a service center near you easily on our website.
Other support information:
“Customer Services Directory (United States and Puerto
Rico)” (
43)
General operation
SC-BTT268_P_eng.book 36 ページ ２０１０年１２月２４日 金曜日 午前１１時１９分