Pioneer DVR-520H - Manual (Page 49)

Recording 06
49
En
This screen shows all the timer programs currently set.
• Each row is for one timer recording program, with the
date and time information, channel, recording mode,
DVD or HDD and recording status.
• The amount of free space available on the HDD and
the currently loaded recordable DVD is shown
towards the bottom of the screen.
• In the lower-right corner, the number of timer
programs already set is shown next to Tmr Pgms.
• If there are more than eight timer programs already
set, press NEXT to switch page (go back using
the PREV button).
• You can also clear a timer program before it’s started
(before the recorder enters timer recording standby)
by highlighting it and pressing
CLEAR.
2 Select ‘New Input’ to set a new timer program,
then press ENTER.
3 Enter the timer recording settings.
Use the
/
(cursor left/right) buttons to select a field;
use the / (cursor up/down) buttons to change the
value.
• Date – Choose a date up to one month in advance, or
select a daily or weekly program.
• Start – Set the recording start time.
• Stop – Set the recording end time (maximum length
of a timer recording is 24 hours for HDD recording or
six hours for DVD).
• CH – Choose a channel (2–69 or 1–125 for antenna or
cable channels respectively, excluding skip
channels), or one of the external inputs from which to
record.
• Mode – Select FINE, SP, LP, EP or AUTO (See
Recording time and picture quality on page 44). If
Manual Recording is on, then you can also select the
MN setting.
• Rec to – Select HDD for hard disk recording or DVD
for DVD recording. Select HDD for Auto Replace
Recording (daily or weekly timer recording only).
• Group – Select a record group (for HDD recording
only).
• Ttl Name Input – Optionally, you can enter a name
for the recording up to 32 characters. (Highlight
Program Set then press (cursor down) to access
this option.)
4 After entering all the timer recording
information, highlight ‘Program set’ and press
ENTER.
The timer recording list screen is displayed again. The
timer program you just input appears in the list. The
rightmost column shows various timer recording status
messages:
• For an HDD timer recording, if there are already 250
titles on the HDD, the message Title Over appears.
• If a timer program overlaps another in the list, the
message Overlap appears.
• 6 Hour Over is displayed if a recording over six hours
is set for a DVD.
• Standby is displayed when the recorder is in timer
recording standby.
• Recording is displayed when a timer recording is in
progress.
5 To exit the timer recording screen, press HOME
MENU.
Note
• The rightmost column in the timer recording screen
( Confirm) shows whether there’s enough space to
record your timer program. If you selected a daily or
weekly program, the date of the last recording that
will fit on the disc appears (up to a maximum of one
month ahead).
• If you set a DVD timer recording but there is no
recordable DVD disc loaded, or the disc loaded
doesn’t have enough free space for the complete
recording,
Recovery is shown. In this case (unless
you load a suitable disc before the recording actually
starts), the recorder will use the HDD for recording.
(The message
Can’t Rec will appear if there are
already 250 titles on the HDD or if there is not enough
free space on the HDD for recording.)
HDD Remain 10h20m(FINE)
DVD Remain 0h43m(FINE)
New Input
Date Start Stop CH Mode Rec to Confirm
1/1
Timer Recording
12/13 MON
12/14 TUE 7:00 PM
9:00 PM 8:00 PM
10:00 PM
32
43 FINE
FINE HDD
HDD OK
OK
Rec to Group
Date Start Stop CH Rec Mode
12/12 SUN 10 00 AM -- --
HDD GROUP1 Program Set
Ttl Name Input
Timer Recording
24 FINE