Maxos – Philips TTX400 User Manual
Page 17
Philips indoor luminaires
8.16
Maxos
Light-line systems
Maxos trapeze reflectors and optics
The sturdy trapeze reflectors for TL5 and TL-D are designed primarily
for applications in industry, supermarkets and shops. They are made of
steel with a white or silver outer finish. The reflectors are optimized
for electrical units holding 1 or 2 TL5/TL-D lamps and provide an
excellent light output ratio.
There are basic trapeze reflectors without an additional mirror inlay
and trapeze reflectors with dedicated aluminum mirror inlays. These
are designed for wide-beam, narrow-beam and asymmetrical wall-
washing light distributions. Moreover, perforated and slotted trapeze
reflectors (without mirror inlays) can be ordered for design reasons or
to create an indirect uplighting effect. For glare reduction, the trapeze
reflector can be equipped with a steel louver.
Emergency lighting, for TL-D only
If emergency lighting by means of separately connected orientation
light units (E27-sockets) is required, special trapeze reflectors with a
bigger cut-off must be used. The length of this reflector corresponds
to that of the 58 W trunking length. A 36 W electrical unit plus the
orientation light unit will fill this length.
Maxos TL5
Trapeze reflectors and optics
Type
4MX692 (TL5 reflector)
4MX693 (TL5 louver/optic)
Suitable electrical unit
For 1- and 2 TL5 49, 54 and 80 W versions
Material and light
distribution
Reflector:
Steel, trapeze (T)
Steel, trapeze (T) with high gloss aluminum
mirror, medium beam (-MB)
Steel, trapeze (T) with high gloss aluminum
mirror, narrow beam (-NB)
Reflector option:
Slotted, direct/indirect (T-S-D/I) or perforated
(T-P)
Louver:
Steel lamellae, white (L-T WH)
Installation
Click-in fixation on electrical unit
Accessory
Trapeze reflector end caps (9MX056 EP1-T WH/
SI)
Remarks
Reflectors and optics are suitable for 1- and 2-
lamp versions
Main applications
Retail and general industry
Maxos TL-D
Trapeze reflectors and optics
Type
4MX092 (TL-D reflector)
4MX093 (TL-D louver/optic)
Suitable electrical unit
For 1 and 2 TL-D 36 and 58 W versions
Material and light
distribution
Reflector:
Steel, trapeze (T)
Steel, trapeze (T), with high gloss aluminum
mirror, wide beam (-WB)
Steel, trapeze (T), with high gloss aluminum
mirror, narrow beam (-NB)
Steel, trapeze (T), with high gloss aluminum
mirror, asymmetrical half reflector (-A)*
Steel, trapeze (T), with high gloss aluminum
mirror, asymmetrical wallwasher (TI-A)*
Reflector option:
Slotted, direct/indirect (T-S-D/I) or perforated
(T-P)
Optic and louver:
Steel lamellae, white (L-T WH) or silver (L-T SI)
Installation
Click-in fixation on electrical unit
Accessory
Trapeze reflector end caps 1 and 2-lamp version
(9MX056 EP1-T WH/SI, 9MX056 EP2-T WH/SI)
Remarks
* For 1-lamp version only
Dedicated reflectors for 1- and 2-lamp TL-D
versions
Main applications
Retail and general industry
Where relevant, for detailed descriptions of Lighting Controls we refer you to chapter 11, and descriptions for e.g. optics/optical covers, lamps data, photometrical diagrams, etc. to the respective sections in chapter 12.
Indoor_2008_Chapter_08_LIS.indb 16
20-05-2008 13:22:32