Panasonic DMR-E65 - Manual (Page 19)

19
RQT7542
Reco
rd
in
g
Timer recording
[RAM] [DVD-R]
You can enter up to 16 programmes up to a month in advance.
Entering S HOW V IEW numbers is an easy way of timer recording. You
can find these numbers in TV listings in newspapers and magazines.
1
Press [ShowView].
2
Press the numbered buttons to enter
the S
HOW V IEW number.
Press [ 2 ] to move back to correct a digit.
3
Press [ENTER].
≥ Confirm the programme and make corrections if necessary
using [
3 , 4 , 2 , 1 ] ( ➡ page 20, step 3).
≥ When “-- ---” appears in the “Name” column, you cannot set
timer recording. Press [
3 , 4 ] to select desired programme
position. After you have entered the information of a TV
station, it is kept in the unit’s memory.
≥ You can also press [REC MODE] to change the recording
mode.
≥ VPS/PDC ( ➡ right)
ON !) OFF (– – –)
≥ Programme Name
Press [
2 , 1 ] to select “Programme Name” and press
[ENTER] ( ➡ page 40).
4
Press [ENTER].
The settings are stored.
Repeat steps 1–4 to programme other recordings.
5
Press [ F TIMER].
The unit turns off and “ F ” lights on the unit’s display to
indicate timer recording standby has been activated.
[RAM]
Even if the unit is in timer recording standby, play starts when you
press [
1 ] (PLAY) or [DIRECT NAVIGATOR]. Timer recording works
even during play.
Using S HOW V IEW number to make timer
recordings
VOLUME CH DIRECT TV REC
DVD
TV
AV
1 2 3
4 5 6
7 8
0
9
MANUAL SKIP
ShowView
CH
CANCEL INPUT SELECT
SKIP
STOP PAUSE PLAY/x1.3
SLOW/SEARCH
FUNCTIONS
ENTER
DIRECT NAVIGATOR
TOP MENU
RETURN SUB MENU
CREATE
CHAPTER
TIMER
EXT LINK
PROG/CHECK
REC MODE ERASE REC
AUDIO
TIME SLIP STATUS DISPLAY
F
A B C
DVD SD/PC DRIVE SELECT
DIRECT
NAVIGATOR
3 , 4,2 , 1
ENTER
F TIMER
PROG/CHECK
EXT LINK
REC MODE
ShowView
PLAY
DVD
¢ CANCEL
Numbered
buttons
1:58 SP ShowView Remain
12:53:00 15. 7. TUE
Enter ShowView Number by using 0-9 key.
Mode Stop Start Name Date
1:58 SP
TIMER
RECORDING
Remain
12:54:00 15. 7. TUE
VPS
PDC
Programme Name
20:00 19:00 15/ 7 TUE SP OFF 1 ARD
∫ To release the unit from recording standby
Press [ F TIMER].
The unit turns on and “ F ” goes out.
≥ Be sure to press [ F TIMER] before the programme start time to
put the unit on recording standby. Timer recording will work only
if “
F ” is displayed.
∫ To cancel recording when recording has
already begun
Press [ F TIMER].
≥ You can also press and hold [ ∫ ] on the main unit for more than
3 seconds to stop recording.
[Note]
≥ “ F ” flashes for about 5 seconds when the unit cannot go to
timer recording standby (e.g., a recordable disc is not in the
disc tray).
≥ If the unit is not put in the timer recording standby mode at the
latest 10 minutes before the programmed timer recording
starting time, the “
F ” flashes on the unit display. In this case,
press [ F TIMER] to put the unit in the timer recording standby
mode.
≥ When you programme successive timer recordings to start
immediately one after the other, the unit cannot record the part
at the beginning of the later programmes (a few seconds when
recording with DVD-RAM and approximately 30 seconds when
recording with DVD-R).
∫ VPS/PDC function ( ➡ page 50)
As long as a VPS/PDC signal is being broadcast by the TV
station, even if the broadcast programme time changes, the
recording time automatically changes to match the new
broadcast time.
To activate the VPS/PDC function
In step 3 in the VPS/PDC column, press [
3 , 4 ] to select “ON”.
SP OK 20:00 19:00 ARD 15/ 7 TUE 01
Mode Disc space Stop Start No. Name Date
1:58 SP TIMER
RECORDING Remain
12:55:00 15. 7. TUE
New Timer Programme
OFF
VPS
PDC
Check to make sure
“OK” is displayed
(
➡ page 21).
19
E65.book 19 ページ ２００４年５月１２日 水曜日 午後２時５３分